No, its not a movie, its a command to get you from the sc> ALOM prompt back to the console or ok prompt.
You must log into the ALOM, then to jump back to the console enter "console -f".
Problem is that this leaves you logged in on the ALOM.
Question: is there an escape key sequence to get... (1 Reply)
Hi guys,
I'm in trouble with a Sunfire T2000.
The OS (Solaris10) is up and running, but I can't log in the sc>I think the terminal server is crashed!
Does anyone know if I can reset the sc> from the OS?
How can I do that?
Thx (6 Replies)
Hi Everyone.
What is the differece b/n ALOM and ALOM CMT Service processor.
I am trying reset ALOM login/passwd using scadm utility on T2000, while I am googling I came cross ALOM CMT doesnt support scadm utility, but ALOM supports.
Not sure how different are these.
Thanks, (0 Replies)
I have a few servers that are all having the same problem when trying to login to their ALOMs. The are T2000's. When I go to login I get the login prompt, but some machines ALOMs aren't responding to the initial login:
# ssh xx.xx.xx.xx
Copyright 2008 Sun Microsystems, Inc. All rights... (9 Replies)
Hi gurus,
I have a sun netra 240 server. I want to get to the ALOM but it always ask for login and password. Can anyone tell me how I can reset the ALOM it to default so I can be able to configure it?
Thanks lots. (2 Replies)
Hello forum,
I have a SUN v250 at home that I have to practice Solaris. I currently have Solaris 9 installed and the ALOM Sun(tm) Advanced Lights Out Manager 1.5.2.
From the ALOM I want to access the console.
sc> console -f
Enter #. to return to ALOM.
after that there is no response.... (19 Replies)
Hi guys,
I'm new with solaris.
I just received sunfire T2000 server.
Problem:
ALOM keep hang/stuck/jammed.
Steps do before it hang :
1. Connect to T2000 (using RJ45 - DB9 cable)
2. Open putty, connect via serial.
3. Power on the server.
4. Its loading.
5. then, hang.
... (1 Reply)
Hi,
How to set ip address on eth0 for access ssh from ALOM? Is it possible? Now i cannot access it because don't have VGA.
I keep try to access using ssh. Please guide me.
Thanks. (16 Replies)
Discussion started by: mzainal
16 Replies
LEARN ABOUT MINIX
dh_systemd_start
DH_SYSTEMD_START(1) Debhelper DH_SYSTEMD_START(1)NAME
dh_systemd_start - start/stop/restart systemd unit files
SYNOPSIS
dh_systemd_start [debhelperoptions] [--restart-after-upgrade] [--no-stop-on-upgrade] [unitfile...]
DESCRIPTION
dh_systemd_start is a debhelper program that is responsible for starting/stopping or restarting systemd unit files in case no corresponding
sysv init script is available.
As with dh_installinit, the unit file is stopped before upgrades and started afterwards (unless --restart-after-upgrade is specified, in
which case it will only be restarted after the upgrade). This logic is not used when there is a corresponding SysV init script because
invoke-rc.d performs the stop/start/restart in that case.
OPTIONS --restart-after-upgrade
Do not stop the unit file until after the package upgrade has been completed. This is the default behaviour in compat 10.
In earlier compat levels the default was to stop the unit file in the prerm, and start it again in the postinst.
This can be useful for daemons that should not have a possibly long downtime during upgrade. But you should make sure that the daemon
will not get confused by the package being upgraded while it's running before using this option.
--no-restart-after-upgrade
Undo a previous --restart-after-upgrade (or the default of compat 10). If no other options are given, this will cause the service to
be stopped in the prerm script and started again in the postinst script.
-r, --no-stop-on-upgrade, --no-restart-on-upgrade
Do not stop service on upgrade.
--no-start
Do not start the unit file after upgrades and after initial installation (the latter is only relevant for services without a
corresponding init script).
NOTES
Note that this command is not idempotent. dh_prep(1) should be called between invocations of this command (with the same arguments).
Otherwise, it may cause multiple instances of the same text to be added to maintainer scripts.
Note that dh_systemd_start should be run after dh_installinit so that it can detect corresponding SysV init scripts. The default sequence
in dh does the right thing, this note is only relevant when you are calling dh_systemd_start manually.
SEE ALSO debhelper(7)AUTHORS
pkg-systemd-maintainers@lists.alioth.debian.org
11.1.6ubuntu2 2018-05-10 DH_SYSTEMD_START(1)