I suffered a fault on a tape drive and would like to redirect my fbackup from /dev/rmt/0m to a NFS Share. I have mounted a NFS share in /mnt/NFSShare. When I run the following command:
With this config file:
It gets to about 21GB in about 15 min then slows down o about 700MB / hour.
Is this to do with the size and if so can I specify multiple files with the "-f" option and how can I limit them to 20GB each?
Thanks for any help.
Dear All,
We have Universe database on HP-UX Servers, when we take back on DDS3 it completes around 48 Gb data on just one tape. As per DDS media specs it can hold upto 24 GB compressed data. How it is managing more than double data..? (3 Replies)
Hi,
I am writing a script that is doing a fbackup during the night and before it shutdown the database then run the fbackup then at the end before restarted the data base, I would like to check the status that the fbackup is fine but I always have warning (about socket: fbackup(1102): WARNING:... (2 Replies)
Hello,
We've recently had a multiple hardrive failure in our legacy HP9000. Now the drives are repaired and the filesystems are recreated, I went to restore the last of the database tables from our dds3 backup, but cannot. Here's what's going on: BTW, I'm an absolute novice w/ HP-UX
The... (5 Replies)
Hey guys im trying fbackup, what kind of device should be used for the output. i tried to put the output into a disk that i LVM and to /tmp but it wont work, theres an error saying that its not a valid device for backup. (14 Replies)
Hi,
I have a fbackup step as below
/bin/nice /etc/fbackup -f /dev/rmt/0m -i / -I /opt/monitrol/tmp/Index.full
Now the errors that i will get in case of the fbackup step, I want to redirect them to a file. Please help me how to redirect to a file.
Thanks,
Avik. (5 Replies)
Hi,
I have a fbackup step as below in HP-UX
/bin/nice /etc/fbackup -f /dev/rmt/0m -i / -I /opt/monitrol/tmp/Index.full
Now the errors that i will get in case of the fbackup step, I want to redirect them to a file. Please help me how to redirect to a file.
Thanks,
Avik. (4 Replies)
Hello,
I'm still new in HP-UX backup and I want to do a FULL BACKUP of HP-UX server to TAPE device. After reading on several forums and posts, i have list down several steps on how to do a full backup on HP-UX with fbackup. I would like the gurus here to comment/advise on the steps below
1)... (4 Replies)
Hi,
I'd like to process multiple files. For example:
file1.txt
file2.txt
file3.txt
Each file contains several lines of data. I want to extract a piece of data and output it to a new file.
file1.txt ----> newfile1.txt
file2.txt ----> newfile2.txt
file3.txt ----> newfile3.txt
Here is... (3 Replies)
Hi!
I'm new in awk and I need some help.
I have a folder with a lot of files and I need that awk do something in each file and print a new file with the output. The input file name should be modified when I print the outpu files.
Thanks in advance for help!
:-)
ciao (5 Replies)
i tried to take a backup by using fbackup command. But it exactly aborted after taking backup of 2GB data. pleasse guide me how should i proceed to overcome this problem.
The command i used is:
fbackup -0 -y -f /dir1 \
-g fbackup_graph \
-c fbackup_config
... (6 Replies)
Discussion started by: siva3492
6 Replies
LEARN ABOUT SUSE
irsend
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)