Sponsored Content
Operating Systems SCO Need Help Installing Legacy System on Newer Hardware Post 302960079 by spock9458 on Tuesday 10th of November 2015 04:51:50 PM
Old 11-10-2015
OK, I understand. I will take another look at my options and maybe try different hardware. I appreciate all of your help, and I might be back again. Thanks!

---------- Post updated at 02:51 PM ---------- Previous update was at 10:37 AM ----------

I am now attempting to install Open Server 5.0.6 on a different server that is from about the same era, and I've gotten it to recognize the hard disk and begin the installation. Now I have a different, less understandable problem.

I will start by saying the CD/DVD drive is recognized in CMOS as the IDE Primary Slave device, and is selected as the first Boot device. The 5.0.6 disk is in that drive and it boots up just fine. When it gets to the part where it lists the devices, however, the drive is not listed - although my hard drive is listed. When installation begins, I get to the point when it asks where my installation files are located, so I select the IDE CD Rom from the list, and I get an error. It says that there is no controller found for the device.

If there is no controller found, how is it reading the disk to get the boot process to start? I don't understand this one, so any help will be appreciated. I know it's been a long time since I've installed this O/S, but I don't remember all of these issues before. Thanks.
 

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

tar --newer = tar --newer-mtime ?

Hi, I have the following question : As far as I know unix doesn't store file creation dates. Would that imply the following? tar -cvzf backup.tar --newer is equal to: tar -cvzf backup.tar --newer-mtime ? (1 Reply)
Discussion started by: jamesbond
1 Replies

2. UNIX for Dummies Questions & Answers

Installing FreeBSD on old system?

I've never had trouble installing freebsd or any linux/unix system on any computer i've tried to do it on. I just recently aquired a Packard Bell, 75mhz Pentium, 482 i believe. Im having difficulty installing it. I have FreeBSD 5.1 on cd and the computer wont even recognize the cd on boot, so it... (2 Replies)
Discussion started by: MadProfessor
2 Replies

3. Solaris

What command to check system hardware

What command can I run on a Solaris 8 server to check the hardware (ie number of processors, speed of processors, installed memory etc). (4 Replies)
Discussion started by: soliberus
4 Replies

4. Solaris

basic hardware & system requirements for solaris 10

hi all, i want to setup a solaris10 lab for 50 trainees. kindly let me know all the basic hardware & system requirements for the lab . with regards, Raj (5 Replies)
Discussion started by: rajp_8007
5 Replies

5. Programming

VERSYS Legacy System

I need help locating the tables that hold the demograhic data in this system on an AIX box. Does anyone know the path? (0 Replies)
Discussion started by: Chelcye
0 Replies

6. AIX

System P hardware

hello everybody, Is there any training to get deep knowledge an hands on lab with system p hardware firmware microcode upgrading etc... thanks in advance (2 Replies)
Discussion started by: Vit0_Corleone
2 Replies

7. Solaris

Manufacturer name of computer system(hardware) , processor

Hi All, Can someone let me know the method or set of commands by which i can retrive manufacturer name of computer system (hardware of machine ) and manufacturer of processor. i get below information when fired psrinfo command : psrinfo -vp The physical processor has 1 virtual processor... (6 Replies)
Discussion started by: omkar.jadhav
6 Replies

8. Red Hat

Hardware and system timing are different

-> We have 2 servers server1 and server2 server. ->server1 is master application and server2 is slave application server. ->output of server1 hardware and slave timing: # hwclock --show Thu 05 Jun 2014 05:34:08 PM SGT -0.465666 seconds # date Thu Jun 5 17:34:16 SGT 2014 # cd... (6 Replies)
Discussion started by: manjusharma128
6 Replies

9. UNIX for Advanced & Expert Users

Linux Command To Find the System Configuration And Hardware Information

Hello guys. I wanted to find the System Configuration and Hardware Information on one of my servers. Here is part of the cpu info: CPU core info: processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 44 model name : Intel(R) Xeon(R) CPU... (2 Replies)
Discussion started by: Ymir
2 Replies
CFREE(3)						     Linux Programmer's Manual							  CFREE(3)

NAME
cfree - free allocated memory SYNOPSIS
#include <stdlib.h> /* In SunOS 4 */ int cfree(void *ptr); /* In glibc or FreeBSD libcompat */ void cfree(void *ptr); /* In SCO OpenServer */ void cfree(char *ptr, unsigned num, unsigned size); /* In Solaris watchmalloc.so.1 */ void cfree(void *ptr, size_t nelem, size_t elsize); Feature Test Macro Requirements for glibc (see feature_test_macros(7)): cfree(): _BSD_SOURCE || _SVID_SOURCE DESCRIPTION
This function should never be used. Use free(3) instead. 1-arg cfree In glibc, the function cfree() is a synonym for free(3), "added for compatibility with SunOS". Other systems have other functions with this name. The declaration is sometimes in <stdlib.h> and sometimes in <malloc.h>. 3-arg cfree Some SCO and Solaris versions have malloc libraries with a 3-argument cfree(), apparently as an analog to calloc(3). If you need it while porting something, add #define cfree(p, n, s) free((p)) to your file. A frequently asked question is "Can I use free(3) to free memory allocated with calloc(3), or do I need cfree()?" Answer: use free(3). An SCO manual writes: "The cfree routine is provided for compliance to the iBCSe2 standard and simply calls free. The num and size argu- ments to cfree are not used." RETURN VALUE
The SunOS version of cfree() (which is a synonym for free(3)) returns 1 on success and 0 on failure. In case of error, errno is set to EINVAL: the value of ptr was not a pointer to a block previously allocated by one of the routines in the malloc(3) family. CONFORMING TO
The 3-argument version of cfree() as used by SCO conforms to the iBCSe2 standard: Intel386 Binary Compatibility Specification, Edition 2. SEE ALSO
malloc(3) COLOPHON
This page is part of release 3.44 of the Linux man-pages project. A description of the project, and information about reporting bugs, can be found at http://www.kernel.org/doc/man-pages/. 2007-07-26 CFREE(3)
All times are GMT -4. The time now is 09:02 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy