Sponsored Content
Operating Systems Linux Add persistent route in cent os 6.5 Post 302959984 by omkar.jadhav on Monday 9th of November 2015 03:28:14 AM
Old 11-09-2015
any suggestions please ..?
 

10 More Discussions You Might Find Interesting

1. AIX

route add

Hello , We have 3 rs/6000 server's running aix on our local network, so each time I try to ping one of these servers we get a "network is down" error , I've been instructed to use to route add command which is ... #route add server.ip router.ip after this the ping command works fine ,... (6 Replies)
Discussion started by: cubicle^dweller
6 Replies

2. IP Networking

Do I need to add a route??

I have two networks connected by cisco routers. My first subnet is 192.168.0.0 and my second is 192.168.1.0. My SCO unix machine is on the 192.168.1.0 subnet with an IP of 192.168.1.231. It can see the entire .1.0 subnet but nothing on the other network. My cicso router(gateway) to the other... (6 Replies)
Discussion started by: agoodrich
6 Replies

3. HP-UX

Add Route on HP-UX v10.x, help.

Hi, My H-UX box has the GW pointing to 10.10.10.1 and I need add it a new route pointing to 192.168.80.x with the GW 10.10.10.13 I tried with: #route add 192.168.80.2 255.255.255.255 10.10.10.13 but I get: add net 192.168.80.0: gateway 255.255.255.0: Network is unreachable I tried with... (4 Replies)
Discussion started by: efrenba
4 Replies

4. IP Networking

Route add probleme

I have a system that i want to reach via a vpn created vi a fierwall.The fierwall in an other system. The ip i am trying to get to is 172.16.4.48 I need to get to it via the hme1 interface. The vpn gateway has this ip 172.30.50.1 I need to clean up the routing table and make this work; or is it... (5 Replies)
Discussion started by: waterboy
5 Replies

5. Solaris

Route Add

Hi, I am trying to add route command in Solaris 10 machine in the following fashion: route add -host 10.8.112.10 180.144.1.250 -interface lo0:1 this command fails with an error "lo0:1: bad value" I want to add a route to 10.8.112.10 that picks 180.144.1.250 as the gateway via the... (3 Replies)
Discussion started by: sudhir_shet
3 Replies

6. IP Networking

route add

I have built a new linux server, via a iLo connection. and I am trying to connect via my desktop to the server I have just built to the management port eth0 via putty. Please could some one advise how to connect to this server from my desktop. Do i need to create add a route access on the... (0 Replies)
Discussion started by: venhart
0 Replies

7. Solaris

Add route to solaris10

Hi need to add 2 routes, one on each server. I know the route add comand but I have always been given the parameters to put in. I need a route in each of the 2 following servers to be able to ping and ssh between them. But how do i know which netmask to put in the route add command ? In... (6 Replies)
Discussion started by: vettec3
6 Replies

8. AIX

Unable to add persistent IP

i am trying to make HACMP but when i add a persistent ip, error shows unable to determine address for 'UPIDGIS1_pers' pls help me out AIX - 5.3 HACMP -5.4 thanks (2 Replies)
Discussion started by: reply.ravi
2 Replies

9. Solaris

Add route to solaris 10

I need to add a new route on solaris10 machine. I want that all traffic on the 23 port (telnet) use 192.168.200.1 gateway. How I do ? Thank you in advance. (1 Reply)
Discussion started by: arfry
1 Replies

10. IP Networking

Add explicit route

Add explicit route to 10.128.255.41/32 , gateway: 10.128.201.254 if not working, please try gateway through management port: 10.128.55.254 Just want to double confirm if this would be the correct command #route add -net 10.128.255.41/32 10.128.201.254 And if didnt work #route add... (1 Reply)
Discussion started by: Thilagarajan
1 Replies
ifmetric(8)						      System Manager's Manual						       ifmetric(8)

NAME
ifmetric - An IPv4 route metrics manipulation tool SYNOPSIS
ifmetric INTERFACE [METRIC] DESCRIPTION
ifmetric is a Linux tool for setting the metrics of all IPv4 routes attached to a given network interface at once. This may be used to change the priority of routing IPv4 traffic over the interface. Lower metrics correlate with higher priorities. ifmetric uses the Linux NETLINK interface to manipulate the routes. Because of that it is compatible with routes created with the new iproute2 utility. OPTIONS
You should specify the interface name as first parameter. The second parameter should be the new metric. If ommited the metric 0 (highest) is used. RETURN VALUES
0 Success 1 Failure AUTHOR
ifmetric was written by Lennart Poettering <mzvszrgevp (at) 0pointer (dot) de>. ifmetric is available at http://0pointer.de/lennart/projects/ifmetric/ SEE ALSO
route(8), ip(8) (iproute2) COMMENTS
This man page was written using xml2man(1) by Oliver Kurth. Manuals User ifmetric(8)
All times are GMT -4. The time now is 02:18 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy