Need Help Installing Legacy System on Newer Hardware Post: 302959835

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

tar --newer = tar --newer-mtime ?

Hi, I have the following question : As far as I know unix doesn't store file creation dates. Would that imply the following? tar -cvzf backup.tar --newer is equal to: tar -cvzf backup.tar --newer-mtime ?

2. UNIX for Dummies Questions & Answers

Installing FreeBSD on old system?

I've never had trouble installing freebsd or any linux/unix system on any computer i've tried to do it on. I just recently aquired a Packard Bell, 75mhz Pentium, 482 i believe. Im having difficulty installing it. I have FreeBSD 5.1 on cd and the computer wont even recognize the cd on boot, so it...

3. Solaris

What command to check system hardware

What command can I run on a Solaris 8 server to check the hardware (ie number of processors, speed of processors, installed memory etc).

4. Solaris

basic hardware & system requirements for solaris 10

hi all, i want to setup a solaris10 lab for 50 trainees. kindly let me know all the basic hardware & system requirements for the lab . with regards, Raj

5. Programming

VERSYS Legacy System

I need help locating the tables that hold the demograhic data in this system on an AIX box. Does anyone know the path?

6. AIX

System P hardware

hello everybody, Is there any training to get deep knowledge an hands on lab with system p hardware firmware microcode upgrading etc... thanks in advance

7. Solaris

Manufacturer name of computer system(hardware) , processor

Hi All, Can someone let me know the method or set of commands by which i can retrive manufacturer name of computer system (hardware of machine ) and manufacturer of processor. i get below information when fired psrinfo command : psrinfo -vp The physical processor has 1 virtual processor...

8. Red Hat

Hardware and system timing are different

-> We have 2 servers server1 and server2 server. ->server1 is master application and server2 is slave application server. ->output of server1 hardware and slave timing: # hwclock --show Thu 05 Jun 2014 05:34:08 PM SGT -0.465666 seconds # date Thu Jun 5 17:34:16 SGT 2014 # cd...

9. UNIX for Advanced & Expert Users

Linux Command To Find the System Configuration And Hardware Information

Hello guys. I wanted to find the System Configuration and Hardware Information on one of my servers. Here is part of the cpu info: CPU core info: processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 44 model name : Intel(R) Xeon(R) CPU...

LEARN ABOUT NETBSD

tcom

TCOM(4) 						   BSD Kernel Interfaces Manual 						   TCOM(4)

NAME

     tcom -- multiplexing serial communications interface

SYNOPSIS

     For 4-port TC-400 series boards:

     tcom0 at isa? port 0x100 irq 5
     com2 at tcom? slave ?
     com3 at tcom? slave ?
     com4 at tcom? slave ?
     com5 at tcom? slave ?

     For 8-port TC-800 series boards:

     tcom0 at isa? port 0x100 irq 5
     com2 at tcom? slave ?
     com3 at tcom? slave ?
     com4 at tcom? slave ?
     com5 at tcom? slave ?
     com6 at tcom? slave ?
     com7 at tcom? slave ?
     com8 at tcom? slave ?
     com9 at tcom? slave ?

DESCRIPTION

     The tcom driver provides support for the Byte Runner Technologies TC-400 and TC-800 series boards that multiplex together up to four or eight
     EIA RS-232C (CCITT V.28) communications interfaces.

     Each tcom device is the master device for up to eight com devices.  The kernel configuration specifies these com devices as slave devices of
     the tcom device, as shown in the synopsis.  The slave ID given for each com device determines which bit in the interrupt multiplexing regis-
     ter is tested to find interrupts for that device.	The port specification for the tcom device is used to compute the base addresses for the
     com subdevices and the port for the interrupt multiplexing register.

     Not all possible configuration options are currently supported (for example, speeds beyond 115200 baud are not currently supported).

FILES

     /dev/tty??

SEE ALSO

     com(4)

HISTORY

     The tcom driver was written by Jukka Marin.

BSD
								   May 20, 1998 							       BSD