11-06-2015
If there is an ide controller, disable it.
There are 6 sata ports on the motherboard; in legacy mode, only 4 are recognized as primary master, primary slave, secondary master, and secondary slave.
Make sure that the disk is connected to the primary master port (probably port 0).
If this still fails, there is a LSI raid controller that is supported, I looked at the mb specs, that has a driver you can download from LSI.
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi,
I have the following question :
As far as I know unix doesn't store file creation dates.
Would that imply the following?
tar -cvzf backup.tar --newer
is equal to:
tar -cvzf backup.tar --newer-mtime ? (1 Reply)
Discussion started by: jamesbond
1 Replies
2. UNIX for Dummies Questions & Answers
I've never had trouble installing freebsd or any linux/unix system on any computer i've tried to do it on. I just recently aquired a Packard Bell, 75mhz Pentium, 482 i believe. Im having difficulty installing it. I have FreeBSD 5.1 on cd and the computer wont even recognize the cd on boot, so it... (2 Replies)
Discussion started by: MadProfessor
2 Replies
3. Solaris
What command can I run on a Solaris 8 server to check the hardware (ie number of processors, speed of processors, installed memory etc). (4 Replies)
Discussion started by: soliberus
4 Replies
4. Solaris
hi all,
i want to setup a solaris10 lab for 50 trainees. kindly let me know all the basic hardware & system requirements for the lab .
with regards,
Raj (5 Replies)
Discussion started by: rajp_8007
5 Replies
5. Programming
I need help locating the tables that hold the demograhic data in this system on an AIX box. Does anyone know the path? (0 Replies)
Discussion started by: Chelcye
0 Replies
6. AIX
hello everybody,
Is there any training to get deep knowledge an hands on lab with system p hardware firmware microcode upgrading etc... thanks in advance (2 Replies)
Discussion started by: Vit0_Corleone
2 Replies
7. Solaris
Hi All,
Can someone let me know the method or set of commands by which i can retrive manufacturer name of computer system (hardware of machine ) and manufacturer of processor. i get below information when fired psrinfo command :
psrinfo -vp
The physical processor has 1 virtual processor... (6 Replies)
Discussion started by: omkar.jadhav
6 Replies
8. Red Hat
-> We have 2 servers server1 and server2 server.
->server1 is master application and server2 is slave application server. ->output of server1 hardware and slave timing:
# hwclock --show Thu 05 Jun 2014 05:34:08 PM SGT -0.465666 seconds # date Thu Jun 5 17:34:16 SGT 2014
# cd... (6 Replies)
Discussion started by: manjusharma128
6 Replies
9. UNIX for Advanced & Expert Users
Hello guys.
I wanted to find the System Configuration and Hardware Information on one of my servers. Here is part of the cpu info:
CPU core info:
processor : 0
vendor_id : GenuineIntel
cpu family : 6
model : 44
model name : Intel(R) Xeon(R) CPU... (2 Replies)
Discussion started by: Ymir
2 Replies
tels(7) Miscellaneous Information Manual tels(7)
NAME
tels, telm - STREAMS Telnet slave (pseudo-terminal) driver, STREAMS Telnet master driver (used by telnetd only), respectively
SYNOPSIS
DESCRIPTION
A Telnet pseudo-terminal consists of a tightly-coupled pair of character devices, called the master device and slave device. The master
and slave device drivers work together to provide a Telnet connection on the server side where the master provides a connection to and the
slave provides a terminal device special file access for the Telnet application processes, as depicted below:
--------------------------
| Pseudo terminal functions|
Application <--> |--------------------------| <--> telnetd
Processes | Slave | Master |
| (tels) | (telm) |
--------------------------
The slave driver, with (STREAMS pty emulation module) and (STREAMS line discipline module) pushed on top (not shown for simplicity), pro-
vides a terminal interface as described in termio(7). Whereas devices that provide the terminal interface described in termio(7) have a
hardware device behind them; in contrast, the slave device has manipulating it through the master side of the Telnet pseudo terminal.
There are no nodes in the file system for each individual master device. Rather, the master driver is set up as a STREAMS clone(7) driver
with its major device number set to the major for the clone driver and its minor device number set to the major for the driver. The master
driver is opened by telnetd using the open(2) system call with as the device file parameter. The clone open finds the next available minor
number for the master device. The master device is available only if it and its corresponding slave device are not already opened.
In order to use the STREAMS Telnet subsystem, a node for the master driver and N number of Telnet slave devices must be installed.
The number of slave devices is set by a kernel tunable parameter called This can be modified using SAM; its default and minimum value is
60. The value of is the upper limit of the number of telnet sessions that can be opened.
Multiple opens are allowed on the Telnet slave device.
The master and slave drivers pass all STREAMS messages to their adjacent drivers. When the connection is closed from the Telnet client
side, an message is sent to the corresponding slave device which will render that slave device unusable. The process on the slave side
gets the errno when attempting a write(2) system call to the slave device file but it will be able to read any data remaining in the slave
stream. Finally, when all the data has been read, the read(2) system call will return 0, indicating that the slave can no longer be used.
AUTHOR
and were developed by HP.
FILES
Streams Telnet master clone device
Streams slave devices where
N is the minor number of the slave device and 0 < N <
SEE ALSO
insf(1M), open(2), ioctl(2), streamio(7), ldterm(7), telnetd(1M), ptem(7).
tels(7)