Can someone please assist ...
below are the entries which i had made as a static route :
but still post restarting network service routing for bond1 is replaced by eth0 as below :
ideally even after network restart it should be : ---------- Post updated 11-06-15 at 03:24 AM ---------- Previous update was 11-05-15 at 04:15 AM ----------
can someone suggest what might be wrong in above case and how to correct it..
Hello ,
We have 3 rs/6000 server's running aix on our local network, so each time I try to ping one of these servers we get a "network is down" error , I've been instructed to use to route add command which is ...
#route add server.ip router.ip
after this the ping command works fine ,... (6 Replies)
I have two networks connected by cisco routers. My first subnet is 192.168.0.0 and my second is 192.168.1.0.
My SCO unix machine is on the 192.168.1.0 subnet with an IP of 192.168.1.231. It can see the entire .1.0 subnet but nothing on the other network.
My cicso router(gateway) to the other... (6 Replies)
Hi,
My H-UX box has the GW pointing to 10.10.10.1 and I need add it a new route pointing to 192.168.80.x with the GW 10.10.10.13
I tried with:
#route add 192.168.80.2 255.255.255.255 10.10.10.13
but I get: add net 192.168.80.0: gateway 255.255.255.0: Network is unreachable
I tried with... (4 Replies)
I have a system that i want to reach via a vpn created vi a fierwall.The fierwall in an other system.
The ip i am trying to get to is 172.16.4.48
I need to get to it via the hme1 interface.
The vpn gateway has this ip 172.30.50.1
I need to clean up the routing table and make this work; or is it... (5 Replies)
Hi,
I am trying to add route command in Solaris 10 machine in the following fashion:
route add -host 10.8.112.10 180.144.1.250 -interface lo0:1
this command fails with an error "lo0:1: bad value"
I want to add a route to 10.8.112.10 that picks 180.144.1.250 as the gateway via the... (3 Replies)
I have built a new linux server, via a iLo connection.
and I am trying to connect via my desktop to the server I have just built to the management port eth0 via putty.
Please could some one advise how to connect to this server from my desktop. Do i need to create add a route access on the... (0 Replies)
Hi need to add 2 routes, one on each server.
I know the route add comand but I have always been given the parameters to put in.
I need a route in each of the 2 following servers to be able to ping and ssh between them. But how do i know which netmask to put in the route add command ?
In... (6 Replies)
i am trying to make HACMP but when i add a persistent ip, error shows unable to determine address for 'UPIDGIS1_pers'
pls help me out
AIX - 5.3
HACMP -5.4
thanks (2 Replies)
I need to add a new route on solaris10 machine.
I want that all traffic on the 23 port (telnet) use 192.168.200.1 gateway.
How I do ?
Thank you in advance. (1 Reply)
Add explicit route to 10.128.255.41/32 , gateway: 10.128.201.254
if not working, please try gateway through management port: 10.128.55.254
Just want to double confirm if this would be the correct command
#route add -net 10.128.255.41/32 10.128.201.254
And if didnt work
#route add... (1 Reply)
Discussion started by: Thilagarajan
1 Replies
LEARN ABOUT DEBIAN
ocf_heartbeat_route
OCF_HEARTBEAT_ROUTE(7) OCF resource agents OCF_HEARTBEAT_ROUTE(7)NAME
ocf_heartbeat_Route - Manages network routes
SYNOPSIS
Route [start | stop | monitor | meta-data | validate-all]
DESCRIPTION
Enables and disables network routes.
Supports host and net routes, routes via a gateway address, and routes using specific source addresses.
This resource agent is useful if a node's routing table needs to be manipulated based on node role assignment. Consider the following
example use case: - One cluster node serves as an IPsec tunnel endpoint. - All other nodes use the IPsec tunnel to reach hosts in a
specific remote network. Then, here is how you would implement this scheme making use of the Route resource agent: - Configure an ipsec LSB
resource. - Configure a cloned Route OCF resource. - Create an order constraint to ensure that ipsec is started before Route. - Create a
colocation constraint between the ipsec and Route resources, to make sure no instance of your cloned Route resource is started on the
tunnel endpoint itself.
SUPPORTED PARAMETERS
destination
The destination network (or host) to be configured for the route. Specify the netmask suffix in CIDR notation (e.g. "/24"). If no
suffix is given, a host route will be created. Specify "0.0.0.0/0" or "default" if you want this resource to set the system default
route. (unique, required, string, no default)
device
The outgoing network device to use for this route. (unique, optional, string, no default)
gateway
The gateway IP address to use for this route. (unique, optional, string, no default)
source
The source IP address to be configured for the route. (unique, optional, string, no default)
table
The routing table to be configured for the route. (optional, string, no default)
SUPPORTED ACTIONS
This resource agent supports the following actions (operations):
start
Starts the resource. Suggested minimum timeout: 20.
stop
Stops the resource. Suggested minimum timeout: 20.
monitor
Performs a detailed status check. Suggested minimum timeout: 20. Suggested interval: 10.
reload
Suggested minimum timeout: 20.
meta-data
Retrieves resource agent metadata (internal use only). Suggested minimum timeout: 5.
validate-all
Performs a validation of the resource configuration. Suggested minimum timeout: 20.
EXAMPLE
The following is an example configuration for a Route resource using the crm(8) shell:
primitive p_Route ocf:heartbeat:Route
params
destination=string
op monitor timeout="20" interval="10" depth="0"
SEE ALSO
http://www.linux-ha.org/wiki/Route_(resource_agent)
AUTHOR
Linux-HA contributors (see the resource agent source for information about individual authors)
resource-agents UNKNOWN 03/09/2014 OCF_HEARTBEAT_ROUTE(7)