10-27-2015
Hp rx2620: is possible to access ILO via serial COM1?
Fast question: a bad reset put ilo ip to 127.0.0.1(!)
and now i cannot reach via network
Is possible to get ilo via serial using COM1/console?
I see three console ports on server back side
two are standard and one is reachable only with this cable...
403 Forbidden
but i don't have this cable.
Question is: there is a way to get ilo access via standard com1/console?
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
looking for the answer to console port access via 25pin serial. Can i tip in from another unix box for access? (5 Replies)
Discussion started by: simplimarvelous
5 Replies
2. AIX
I have installed aix 5.2 on aix box through serial console connected to COM 1 . I even get a login prompt after the fresh installation . But as soon as i give a root & enter i again get a login prompt.i..e I am not able to logon after a fresh installation.
and even i configured IP configuration... (0 Replies)
Discussion started by: linuxnightowl84
0 Replies
3. UNIX for Advanced & Expert Users
I have an application that requires me to disable the restricted access to the X Server libraries by issuing the 'Xhost +' command from a Console Window.
It is important that this command is run from the Console Window and not a Terminal Window otherwise the system complains that DISPLAY is not... (0 Replies)
Discussion started by: jimthompson
0 Replies
4. Solaris
Greetings All,
If someone/anyone reading this post has had success setting up and configuring HP iLO2 CLI virtual serial port for Solaris...please tell how.
I'm trying to get a remote console to an HP DL385 server via iLO2 and ssh. The server is running Solaris 10 (11/06), patched to... (1 Reply)
Discussion started by: alias.256
1 Replies
5. Shell Programming and Scripting
friends,
i have a gizmo ( vk011) that plugs into my comport ( centOS5.3 )
this I listen to via minicom and it will spit out the temp in the room like this.
Sensor 1 +70.13 DegF Hi +77.56 DegF Low +29.75 DegF
Sensor 1 +70.13 DegF Hi +77.56 DegF Low +29.75 DegF
Sensor 1 +70.13 DegF Hi +77.56... (0 Replies)
Discussion started by: zimbot
0 Replies
6. Ubuntu
Hello!
I am working on an application which reads environmental instruments which have serial ports. The application requires a serial port to be present to talk to the device (i.e. /dev/ttyS0 ). In some instances the environmental devices will be 100's of yards away from the computer, so a... (5 Replies)
Discussion started by: mvona
5 Replies
7. Solaris
Hello Folks,
I am having trouble to login to rsc or serial console of V890.
The rsc2.2.3 has been configured with required parameters, resetrs and even rebooted. When serial port is connected to laptop, The hyper terminal does not get the console or POSt messages when the server is rebooting... (8 Replies)
Discussion started by: defflepord
8 Replies
8. HP-UX
how to set IP for iLO in HP server first time
thanks to all (1 Reply)
Discussion started by: sijocg
1 Replies
9. Solaris
I am trying to use a serial communications device that is connected to /dev/ttyb on a netra 240 server. This is a solaris zone configuration using solaris 10 0910. I am able to access /dev/ttyb from the global zone but not throught he non-global zone. I have enabled all of the tty devices in my... (0 Replies)
Discussion started by: disagreeable
0 Replies
10. HP-UX
Hi there,
hope you can help since I'm a novice and playing with this machine to maybe one day use it with our non-profit art project (plantage9.de).
I have the proper media for itanium and everything seems okay, loads the DVD etc., until it halts without any progress for hours (see also image... (1 Reply)
Discussion started by: plantage
1 Replies
LEARN ABOUT OSX
tk_initconsolechannels
Tk_InitConsoleChannels(3) Tk Library Procedures Tk_InitConsoleChannels(3)
__________________________________________________________________________________________________________________________________________________
NAME
Tk_InitConsoleChannels - Install the console channels as standard channels
SYNOPSIS
#include <tk.h>
Tk_InitConsoleChannels(interp)
ARGUMENTS
Tcl_Interp *interp (in) Interpreter in which the console channels are created.
_________________________________________________________________
DESCRIPTION
Tk_InitConsoleChannels is invoked to create a set of console channels and install them as the standard channels. All I/O on these channels
will be discarded until Tk_CreateConsoleWindow is called to attach the console to a text widget.
This function is for use by shell applications based on Tk, like wish, on platforms which have no standard channels in graphical mode, like
Win32.
The interp argument is the interpreter in which to create and install the console channels.
NOTE: If this function is used it has to be called before the first call to Tcl_RegisterChannel, directly, or indirectly through other
channel functions. Because otherwise the standard channels will be already initialized to the system defaults, which will be nonsensical
for the case Tk_InitConsoleChannels is for.
SEE ALSO
console(n)
KEYWORDS
standard channels, console
Tk 8.5 Tk_InitConsoleChannels(3)