10-12-2015
Hi!
I have checked the vendor details and it is reporting correctly as the new storage. I tried naming it, however, it is adding the name to the end what is getting displayed. I believe it is a cosmetic issue and may have to live with it unless there is an option to change it.
Thanks for the help!
BR,
Bhaskar
9 More Discussions You Might Find Interesting
1. Solaris
We get the error "NO HARD Disks found" while installing Solaris 10 (latest-6/06) on Poweredge 2950.
We found that the LSISAS1068 driver is needed for this. But the provision is given only to install the driver using the floppy (in downloads site). But we dont have a floppy drive in our system... (12 Replies)
Discussion started by: S.Vishwanath
12 Replies
2. Shell Programming and Scripting
Can someone help me to convert the date format after get it from the "LAST REBOOT" command.
these is the standard output.
bash-3.00# last reboot
reboot system boot Fri Aug 6 15:07
reboot system down Fri Aug 6 15:04
reboot system boot ... (3 Replies)
Discussion started by: pichitw
3 Replies
3. Shell Programming and Scripting
Hi,
I have line in input file as below:
3G_CENTRAL;INDONESIA_(M)_TELKOMSEL;SPECIAL_WORLD_GRP_7_FA_2_TELKOMSEL
My expected output for line in the file must be :
"1-Radon1-cMOC_deg"|"LDIndex"|"3G_CENTRAL|INDONESIA_(M)_TELKOMSEL"|LAST|"SPECIAL_WORLD_GRP_7_FA_2_TELKOMSEL"
Can someone... (7 Replies)
Discussion started by: shis100
7 Replies
4. Solaris
I'm posting here as it didn't seem quite right in the hardware section (as it's LOM commands). My apologies if I have that wrong though :)
I've finally gotten round to configuring the LOM on my Netra X1, but I can't get it to change the hostname via the "set" command:
lom>show hostname... (2 Replies)
Discussion started by: Smiling Dragon
2 Replies
5. Shell Programming and Scripting
Hi Experts,
I have a string with colon delimited, want 2nd colon to be changed to a pipe.
data:
101:8:43:4:72:14:41:69:85:3:137:4:3:0:4:0:9:3:0:3:12:3:
I am trying with sed, but can change only 1 occurance:
echo "101:8:43:4:72:14:41:69:85:3:137:4:3:0:4:0:9:3:0:3:12:3:" | sed 's/:/|/2'... (5 Replies)
Discussion started by: rveri
5 Replies
6. Shell Programming and Scripting
I have a bunch of random character lines like ABCEDFG. I want to find all lines with "A" and then change any "E" to "X" in the same line. ALL lines with "A" will have an "X" somewhere in it. I have tried sed awk and vi editor. I get close, not quite there. I know someone has already solved this... (10 Replies)
Discussion started by: nightwatchrenba
10 Replies
7. UNIX for Advanced & Expert Users
Hi, everyone.
I need to write a program to get io info based on libperfstat.
But the "write time" of a disk is just half of the value get from iostat.
I'm confused and can't explain. Help please.
How I calculate "write service time per sec":
In iostat:
write service... (0 Replies)
Discussion started by: jackliang
0 Replies
8. UNIX for Dummies Questions & Answers
How to use "mailx" command to do e-mail reading the input file containing email address, where column 1 has name and column 2 containing “To” e-mail address
and column 3 contains “cc” e-mail address to include with same email.
Sample input file, email.txt
Below is an sample code where... (2 Replies)
Discussion started by: asjaiswal
2 Replies
9. Shell Programming and Scripting
Ladies & Gents,
Can one of you gurus please show me a very simple "expect" script to change the password in Solaris in a script, please? Nothing fancy, no error checking, no nothing. Just to change the password of a new user, it's all.
Many thanks in advance. U guys have honestly earned my... (1 Reply)
Discussion started by: Hiroshi
1 Replies
LEARN ABOUT SUNOS
addbadsec
addbadsec(1M) System Administration Commands addbadsec(1M)
NAME
addbadsec - map out defective disk blocks
SYNOPSIS
addbadsec [-p] [ -a blkno [blkno...]] [-f filename] raw_device
DESCRIPTION
addbadsec is used by the system administrator to map out bad disk blocks. Normally, these blocks are identified during surface analysis,
but occasionally the disk subsystem reports unrecoverable data errors indicating a bad block. A block number reported in this way can be
fed directly into addbadsec, and the block will be remapped. addbadsec will first attempt hardware remapping. This is supported on SCSI
drives and takes place at the disk hardware level. If the target is an IDE drive, then software remapping is used. In order for software
remapping to succeed, the partition must contain an alternate slice and there must be room in this slice to perform the mapping.
It should be understood that bad blocks lead to data loss. Remapping a defective block does not repair a damaged file. If a bad block
occurs to a disk-resident file system structure such as a superblock, the entire slice might have to be recovered from a backup.
OPTIONS
The following options are supported:
-a Adds the specified blocks to the hardware or software map. If more than one block number is specified, the entire list should be
quoted and block numbers should be separated by white space.
-f Adds the specified blocks to the hardware or software map. The bad blocks are listed, one per line, in the specified file.
-p Causes addbadsec to print the current software map. The output shows the defective block and the assigned alternate. This option
cannot be used to print the hardware map.
OPERANDS
The following operand is supported:
raw_device The address of the disk drive (see FILES).
FILES
The raw device should be /dev/rdsk/c?[t?]d?p0. See disks(1M) for an explanation of SCSI and IDE device naming conventions.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Architecture |x86 |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
SEE ALSO
disks(1M), diskscan(1M), fdisk(1M), fmthard(1M), format(1M), attributes(5)
NOTES
The format(1M) utility is available to format, label, analyze, and repair SCSI disks. This utility is included with the addbadsec,
diskscan(1M), fdisk(1M), and fmthard(1M) commands available for x86. To format an IDE disk, use the DOS "format" utility; however, to
label, analyze, or repair IDE disks on x86 systems, use the Solaris format(1M) utility.
SunOS 5.10 24 Feb 1998 addbadsec(1M)