10-09-2015
Well, that's embarrassing! I thought I had tried that command and that it failed. But it worked just fine. Thank you.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Whenever I try to uncompress file.tar.gz I always get message 'tar: directory checksum error'. I think because of this some of the directories might not be uncompressing properly. Why do I get this message? I do uncompress on UNIX Solaris 5.8. Oh, if I do the same thing on Fedora 3 everything works... (14 Replies)
Discussion started by: webtekie
14 Replies
2. UNIX for Dummies Questions & Answers
Dear experts
I have received a tar file containing several files with full path. Now I need to restore it in another system but when I want to extract files by using
tar -xvf tarfile
it wants to create all files with full paths again in new system in which I don't have enough previleges.
How... (4 Replies)
Discussion started by: Reza Nazarian
4 Replies
3. Shell Programming and Scripting
hi all,
kindly help me how to extract one file form .tar.gz without uncompressing .tar.gz file.
thanks in advance
bali (2 Replies)
Discussion started by: balireddy_77
2 Replies
4. UNIX Desktop Questions & Answers
Can I extract files from an archive file (tar), where the filename includes the full directory path, to a different directory?
For example the archive files may have a filename of
/SrcFiles/XXX/filename.dat
and I want to extract it to /SrcFiles/YYY/filename.dat. Since the archive file... (1 Reply)
Discussion started by: nmalencia
1 Replies
5. UNIX for Dummies Questions & Answers
Can I extract files from an archive file (tar), where the filename includes the full directory path, to a different directory?
For example the archive files may have a filename of
/SrcFiles/XXX/filename.dat
and I want to extract it to /SrcFiles/YYY/filename.dat. Since the archive file was... (1 Reply)
Discussion started by: nmalencia
1 Replies
6. Shell Programming and Scripting
Hi All,
I want to read the content of the particular file from tar.Z without extracting.
aaa.tar.Z contains a file called one.txt, I want to read the content of the one.txt without extracting.
Please help me to read the content of it.
Regards,
Kalai. (12 Replies)
Discussion started by: kalpeer
12 Replies
7. Solaris
Is there an option in tar which deletes the .tar file as soon as it is successfully extracted. (5 Replies)
Discussion started by: vickylife
5 Replies
8. Solaris
Hi Gurus,
I have a .tar file which required untar to the new location. I list the content with –tvf its listing the files which are inside the tar, when I am extracting he file from tar its working fine, however once I am trying to extract the file at the new location I am unable to do so. I... (11 Replies)
Discussion started by: kumarmani
11 Replies
9. UNIX for Dummies Questions & Answers
I have tried:
tar -xfv mytarfile.tar archive/tabv/*
tar -xfv mytarfile.tar --wildcards 'archive/tabv/*'
tar -xf mytarfile.tar -v --wildcards 'archive/tabv/*'
tar -xfv mytarfile.tar --wildcards --no-anchored 'archive/tabv/*'
tar -xfv mytarfile.tar --wildcards `archive/tabv/*`
and none... (5 Replies)
Discussion started by: zapper222
5 Replies
10. UNIX for Advanced & Expert Users
Hi,
I want to tar files and zip them in order to clean up space in directory. I have files like /path/file1 /path file2.
What I am trying to do is:
Option 1:
tar -cvf /path/file1 /path file2 | gzip > test.tar.gz
I got the file created. But while trying to extract the Tar and zipped file, I... (1 Reply)
Discussion started by: Quesemail
1 Replies
IPS(4) BSD Kernel Interfaces Manual IPS(4)
NAME
ips -- IBM/Adaptec ServeRAID controller driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device pci
device scbus
device ips
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
ips_load="YES"
DESCRIPTION
The ips driver claims to support the IBM (now Adaptec) ServeRAID series SCSI controller cards.
These cards come with a built in configuration utility stored in the firmware known as the ISPR. This utility is accessed with the <Ctrl+I>
key combination during the initial card POST.
It is highly recommended that this utility be used to configure the card before attempting to diagnose the below error messages.
In some cases, the ips driver can have difficulties attaching during the system initialization period. To avoid these difficulties, set the
hw.ips.0.disable tunable to 1. It will prevent the driver from attaching.
HARDWARE
Controllers supported by the ips driver include:
o IBM ServeRAID 3H
o ServeRAID 4L/4M/4H
o ServeRAID Series 5
o ServeRAID 6i/6M
o ServeRAID 7t/7k/7M
DIAGNOSTICS
Several error codes may be shown when the card initializes the IBM ISPR utility and are independent of FreeBSD.
ips%d: failed to get adapter configuration data from device
ips%d: failed to get drive configuration data from device
Unable to obtain adapter or drive configuration.
ips%d iobuf error
A buffer input/output error has occurred. [ENXIO]
General adapter errors:
Attaching bus failed
This message is undocumented.
WARNING: command timeout. Adapter is in toaster mode, resetting
A command timeout has caused the adapter to be reset.
AIEE! adapter reset failed, giving up and going home! Have a nice day
An error occurred while attempting to reset the adapter.
unable to get adapter configuration
unable to get drive configuration
There was an error when attempting to get configuration information.
Adapter error during initialization.
adapter initialization failed
There was an error while attempting to initialize the adapter.
adapter failed config check
adapter clear failed
There was an error while checking the adapter.
device is disabled
The adapter is disabled.
resource allocation failed
irq allocation failed
irq setup failed
The driver was unable to allocate resources for the device.
Error messages due to DMA:
can't alloc command dma tag
can't alloc SG dma tag
can't alloc dma tag for statue queue
dmamap failed
Failure to map or allocate DMA resources.
Cache, buffer, and command errors:
failed to initialize command buffers
no mem for command slots!
The ips driver will return [ENOMEM] in such cases.
ERROR: unable to get a command! can't flush cache!
ERROR: cache flush command failed!
ERROR: unable to get a command! can't update nvram
ERROR: nvram update command failed!
ERROR: unable to get a command! can't sync cache!
ERROR: cache sync command failed!
ERROR: unable to get a command! can't sync cache!
ERROR: etable command failed!
COMPATIBILITY
Unlike many of the other SCSI devices in FreeBSD, the ips driver does not use the cam(4) SCSI subsystem.
SEE ALSO
ch(4), da(4), sysctl(8)
AUTHORS
The ips driver was written by David Jefferys and Scott Long <scottl@FreeBSD.org>.
This manual page was written by Tom Rhodes <trhodes@FreeBSD.org>.
BSD
November 4, 2006 BSD