10-08-2015
Hi
here i am using network packet brokering device.
9 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
hi all
I process is sleeping after 12 hours but i need to be run this to 24 hours but it goes in sleep mode after 12 hours what should i do to make process always running.Kindly give me suggestion. (0 Replies)
Discussion started by: mukesh_rakesh1
0 Replies
2. Shell Programming and Scripting
how to start a process and make it sleep for 5 mins and then kill that process (6 Replies)
Discussion started by: shrao
6 Replies
3. UNIX for Dummies Questions & Answers
I'm running an Apache server on Ubuntu. When I try to call fopen() in PHP, I get a bunch of permission errors. I searched for advice on this, and I found that I needed to change the system account that Apache runs on. However, I'm not sure how to do this, and I was unable to find the answer on... (3 Replies)
Discussion started by: gloriac991
3 Replies
4. UNIX for Advanced & Expert Users
I've tried this a long time ago and was successful but could not remember how i did it. Tried ctrl+Z and then used bg %
could not figure what i did after to keep it no hangup -
not sure if used nohup -p pid, can u plz help me out if this can be done.
Any help will be appreciated. (12 Replies)
Discussion started by: pharos467
12 Replies
5. Shell Programming and Scripting
Hello all,
I would be happy if any one could help me with a shell script that would determine all the processes running on a Unix server and post a mail if any of the process is not running or aborted.
Thanks in advance
Regards,
pradeep kulkarni.
:mad: (13 Replies)
Discussion started by: pradeepmacha
13 Replies
6. Shell Programming and Scripting
Hi,
Can anyone help to create a script that will kill the process which is in hang state. (1 Reply)
Discussion started by: A.Santhosh
1 Replies
7. Red Hat
when system is hung state due to swap, we will reboot it through ILO.
i want to know which process caused system hung. (1 Reply)
Discussion started by: Naveen.6025
1 Replies
8. BSD
Hi Experts,
I am facing one problem here which is one process always stuck in running state which causes the other similar process to sleep state . This causes my system in hanged state.
On doing cat /proc/<pid>wchan showing the "__init_begin" in the output.
Can you please help me here... (0 Replies)
Discussion started by: naveeng
0 Replies
9. UNIX for Advanced & Expert Users
Hi Experts,
I am facing one problem here which is one process always stuck in running state which causes the other similar process to sleep state . This causes my system in hanged state.
On doing cat /proc/<pid>wchan showing the "__init_begin" in the output.
Can you please help me here... (1 Reply)
Discussion started by: naveeng
1 Replies
UHSO(4) BSD Kernel Interfaces Manual UHSO(4)
NAME
uhso -- support for several HSxPA devices from Option N.V.
SYNOPSIS
The module can be loaded at boot time by placing the following line in loader.conf(5):
uhso_load="YES"
DESCRIPTION
The uhso driver provides support for several HSxPA devices from Option N.V. that are based on their packet interface. Each device has a set
of serial ports and a raw IP packet interface. The serial ports of the device are accessed through the ucom(4) driver which makes them
behave like tty(4) devices. The packet interface is exposed as a network interface.
Establishing a connection on the packet interface is achieved by using the proprietary AT commands ``AT_OWANCALL'' and ``AT_OWANDATA'' on any
of the available serial ports.
The network interface must be configured manually using the data obtain from these calls.
Each device usually have at least two or more serial ports, their individual purpose can be identified through sysctl(8). Ports identified
as ``Modem'' features a normal modem interface that can be used with PPP. Ports identified as ``Diagnostic'' uses a proprietary binary
interface used for firmware upgrades, this port does not have a AT command interface and can not be used to control the device. Other ports
features an AT command interface that can be used for normal device control.
HARDWARE
The uhso driver should work with most devices from Option. The following devices have been verified to work
o Option GlobeSurfer iCON 7.2 (new firmware)
o Option iCON 225
o Option iCON 452
o Option iCON 505
The device features a mass storage device referred to as ``Zero-CD'' which contains drivers for Microsoft Windows; this is the default mode
for the device. The uhso driver automatically switches the device from ``Zero-CD'' mode to modem mode. This behavior can be disabled by
setting hw.usb.uhso.auto_switch to 0 using sysctl(8)
EXAMPLES
Establishing a packet interface connection using the AT command interface available at one of the serial ports
AT+CGDCONT=1,,"apn.provider"
AT_OWANCALL=1,1,1
OK
_OWANCALL=1,1
AT_OWANDATA=1
_OWANDATA: 1, 10.11.12.13, 0.0.0.0, 10.2.3.4, 10.2.3.5,
0.0.0.0, 0.0.0.0, 72000
Configuring the interface
ifconfig uhso0 10.11.12.13 up
route add default -interface uhso0
echo "nameserver 10.2.3.4" > /etc/resolv.conf
echo "nameserver 10.2.3.5" >> /etc/resolv.conf
The connection can be terminated with
AT_OWANCALL=1,0,1
FILES
/dev/cuaU?.?
SEE ALSO
ucom(4), usb(4)
AUTHORS
The uhso driver was written by Fredrik Lindberg <fli@shapeshifter.se>.
BSD
January 14, 2010 BSD