Sponsored Content
Operating Systems Solaris Solaris 10: how to disable an unused HBA card Post 302957072 by DukeNuke2 on Tuesday 6th of October 2015 04:13:38 PM
Old 10-06-2015
You can disable the PCI slot in BIOS...
 

10 More Discussions You Might Find Interesting

1. Solaris

HBA Card

Hello...I got a problem here. I have HBAs installed in one of the domains in E20 and I gotta find out the brand and firmware. But when I do a prtconf, I cannot see the HBA. For other servers installed with HBAs, when I do prtconf on them I can see either qlc or em. Can you guys enlighten me how to... (5 Replies)
Discussion started by: xiaochensg
5 Replies

2. Solaris

Qlogic HBA card in E450 with errors

I have installed a qlogic HBA card in an E450 Solaris 9 with all the SUNW packages and the latest EPROM version. Configuration reboot was done. An orange light flashes to the right of where the card plugs into the fiber cable after booting, and the following error apprears at the start of the boot... (9 Replies)
Discussion started by: floydm
9 Replies

3. Solaris

istall sas raid HBA internal card

I need to install a raid HBA internal card on a T5240. The reason is I have more drives and the current mother board controller does not support more than 4 drives. My question is I have raidctl set up on current drives. If I install new HBA card do I have to delete current raidctl and... (3 Replies)
Discussion started by: photon
3 Replies

4. Solaris

Install Solaris 10 with an internal StorageTek SAS HBA Raid card

Hi all i would like to ask some suggests about my next job! I have to install a new Sun Netra T5220, with an additional internal StorageTek SAS HBA Raid. The problem come in if every disk is now controlled by the HBA, how can I install the OS? No disk is being detected by the OS. SAS card... (2 Replies)
Discussion started by: kakabobo
2 Replies

5. UNIX for Advanced & Expert Users

Sun internal disks and HBA card

I have a V490 that has couple internal disks attached to the same dual-port HBA card that I'm planning attach to the SAN for additional storage. Would I sacrifice performance if I use the same HBA? Is it better to throw in a new HBA instead? (1 Reply)
Discussion started by: kiem
1 Replies

6. AIX

Need HBA card driver

Hi All, SUN emulex HBA card has been installed on P520 box. When i run the cfgmgr i am getting the following message. lpar2#cfgmgr cfgmgr: 0514-621 WARNING: The following device packages are required for device support but are not currently installed.... (0 Replies)
Discussion started by: b_manu78
0 Replies

7. Solaris

How to enable hba port of a two port hba card

Hi, i have a two port hba card in solaris 10 system one of which is disabled. How to enable and configure the other port. ---------- Post updated at 08:17 AM ---------- Previous update was at 03:40 AM ---------- please help :( (7 Replies)
Discussion started by: rishiraaz
7 Replies

8. Solaris

Extracting HBA Card Hardware info

Hello, I am very new to solaris so please bear with me. I have 2 machines in question. For both I am trying to get the HBA Card Hardware information such as: HBA Model Name HBA Firmware version HBA Port details HBA Driver details First machine is a Solaris 10. When I execute fcinfo... (6 Replies)
Discussion started by: flagman5
6 Replies

9. Solaris

Which FC HBA card support Solaris9

I have JNI FCE-6460-N fc card , it is detected in OK prompt.....I connected Sun StorEDGE A5000 FC storage. in OK prompt, PROBE-SCSI-ALL showing A5000 fc hdds details in ok prompt..... but in OS level.....not showing the hdd, i tried in DEVFSADM command and FORMAT command not showing A5000... (3 Replies)
Discussion started by: anysystem
3 Replies

10. Red Hat

HBA card faulty

Hi, How to determine if HBA card in getting faulty from linux host ? any pointers. (2 Replies)
Discussion started by: saurabh84g
2 Replies
PCI_CREATE_SLOT(9)						Hardware Interfaces						PCI_CREATE_SLOT(9)

NAME
pci_create_slot - create or increment refcount for physical PCI slot SYNOPSIS
struct pci_slot * pci_create_slot(struct pci_bus * parent, int slot_nr, const char * name, struct hotplug_slot * hotplug); ARGUMENTS
parent struct pci_bus of parent bridge slot_nr PCI_SLOT(pci_dev->devfn) or -1 for placeholder name user visible string presented in /sys/bus/pci/slots/<name> hotplug set if caller is hotplug driver, NULL otherwise DESCRIPTION
PCI slots have first class attributes such as address, speed, width, and a struct pci_slot is used to manage them. This interface will either return a new struct pci_slot to the caller, or if the pci_slot already exists, its refcount will be incremented. Slots are uniquely identified by a pci_bus, slot_nr tuple. There are known platforms with broken firmware that assign the same name to multiple slots. Workaround these broken platforms by renaming the slots on behalf of the caller. If firmware assigns name N to MULTIPLE SLOTS
The first slot is assigned N The second slot is assigned N-1 The third slot is assigned N-2 etc. PLACEHOLDER SLOTS
In most cases, pci_bus, slot_nr will be sufficient to uniquely identify a slot. There is one notable exception - pSeries (rpaphp), where the slot_nr cannot be determined until a device is actually inserted into the slot. In this scenario, the caller may pass -1 for slot_nr. The following semantics are imposed when the caller passes slot_nr == -1. First, we no longer check for an existing struct pci_slot, as there may be many slots with slot_nr of -1. The other change in semantics is user-visible, which is the 'address' parameter presented in sysfs will CONSIST SOLELY OF A DDDD
bb tuple, where dddd is the PCI domain of the struct pci_bus and bb is the bus number. In other words, the devfn of the 'placeholder' slot will not be displayed. COPYRIGHT
Kernel Hackers Manual 2.6. July 2010 PCI_CREATE_SLOT(9)
All times are GMT -4. The time now is 01:35 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy