10-06-2015
is it a PCI-e card? or does it use SFPs? if it does just remove it.
10 More Discussions You Might Find Interesting
1. Solaris
Hello...I got a problem here. I have HBAs installed in one of the domains in E20 and I gotta find out the brand and firmware. But when I do a prtconf, I cannot see the HBA. For other servers installed with HBAs, when I do prtconf on them I can see either qlc or em. Can you guys enlighten me how to... (5 Replies)
Discussion started by: xiaochensg
5 Replies
2. Solaris
I have installed a qlogic HBA card in an E450 Solaris 9 with all the SUNW packages and the latest EPROM version. Configuration reboot was done. An orange light flashes to the right of where the card plugs into the fiber cable after booting, and the following error apprears at the start of the boot... (9 Replies)
Discussion started by: floydm
9 Replies
3. Solaris
I need to install a raid HBA internal card on a T5240. The reason is I have
more drives and the current mother board controller does not support more
than 4 drives.
My question is I have raidctl set up on current drives. If I install new HBA
card do I have to delete current raidctl and... (3 Replies)
Discussion started by: photon
3 Replies
4. Solaris
Hi all
i would like to ask some suggests about my next job!
I have to install a new Sun Netra T5220, with an additional internal StorageTek SAS HBA Raid.
The problem come in if every disk is now controlled by the HBA, how can I install the OS?
No disk is being detected by the OS.
SAS card... (2 Replies)
Discussion started by: kakabobo
2 Replies
5. UNIX for Advanced & Expert Users
I have a V490 that has couple internal disks attached to the same dual-port HBA card that I'm planning attach to the SAN for additional storage.
Would I sacrifice performance if I use the same HBA?
Is it better to throw in a new HBA instead? (1 Reply)
Discussion started by: kiem
1 Replies
6. AIX
Hi All,
SUN emulex HBA card has been installed on P520 box.
When i run the cfgmgr i am getting the following message.
lpar2#cfgmgr
cfgmgr: 0514-621 WARNING: The following device packages are required for
device support but are not currently installed.... (0 Replies)
Discussion started by: b_manu78
0 Replies
7. Solaris
Hi,
i have a two port hba card in solaris 10 system one of which is disabled. How to enable and configure the other port.
---------- Post updated at 08:17 AM ---------- Previous update was at 03:40 AM ----------
please help :( (7 Replies)
Discussion started by: rishiraaz
7 Replies
8. Solaris
Hello,
I am very new to solaris so please bear with me. I have 2 machines in question. For both I am trying to get the HBA Card Hardware information such as:
HBA Model Name
HBA Firmware version
HBA Port details
HBA Driver details
First machine is a Solaris 10. When I execute fcinfo... (6 Replies)
Discussion started by: flagman5
6 Replies
9. Solaris
I have JNI FCE-6460-N fc card , it is detected in OK prompt.....I connected Sun StorEDGE A5000 FC storage.
in OK prompt, PROBE-SCSI-ALL
showing A5000 fc hdds details in ok prompt.....
but in OS level.....not showing the hdd, i tried in DEVFSADM command and FORMAT command not showing A5000... (3 Replies)
Discussion started by: anysystem
3 Replies
10. Red Hat
Hi,
How to determine if HBA card in getting faulty from linux host ? any pointers. (2 Replies)
Discussion started by: saurabh84g
2 Replies
LEARN ABOUT SUNOS
tran_sync_pkt
tran_sync_pkt(9E) Driver Entry Points tran_sync_pkt(9E)
NAME
tran_sync_pkt - SCSI HBA memory synchronization entry point
SYNOPSIS
#include <sys/scsi/scsi.h>
void prefixtran_sync_pkt(struct scsi_address *ap, struct scsi_pkt *pkt);
INTERFACE LEVEL
Solaris architecture specific (Solaris DDI).
PARAMETERS
ap A pointer to a scsi_address(9S) structure.
pkt A pointer to a scsi_pkt(9S) structure.
DESCRIPTION
The tran_sync_pkt() vector in the scsi_hba_tran(9S) structure must be initialized during the HBA driver's attach(9E) to point to an HBA
driver entry point to be called when a target driver calls scsi_sync_pkt(9F).
tran_sync_pkt() must synchronize a HBA's or device's view of the data associated with the pkt, typically by calling ddi_dma_sync(9F). The
operation may also involve HBA hardware-specific details, such as flushing I/O caches, or stalling until hardware buffers have been
drained.
SEE ALSO
attach(9E), tran_init_pkt(9E), ddi_dma_sync(9F), scsi_hba_attach(9F), scsi_init_pkt(9F), scsi_sync_pkt(9F), scsi_address(9S),
scsi_hba_tran(9S), scsi_pkt(9S)
Writing Device Drivers
NOTES
A target driver may call tran_sync_pkt() on packets for which no DMA resources were allocated.
SunOS 5.10 1 Nov 1993 tran_sync_pkt(9E)