Sponsored Content
Operating Systems SCO Backup/RAID of HD on Old UNIX Server Post 302956646 by hicksd8 on Thursday 1st of October 2015 02:25:12 PM
Old 10-01-2015
It seems that your software is not protected via FlexLM then.
This User Gave Thanks to hicksd8 For This Post:
 

9 More Discussions You Might Find Interesting

1. Filesystems, Disks and Memory

2-Ch RAID Problem in SCO Open Server

Help, if possible. In SCO Open Server with installation of two-channel RAID controller the following happens: on the channel 0 disk array is seen by an operational system, and on the channel 1 array is not seen (simultaneously). That is the operational system can not simultaneously use more than... (1 Reply)
Discussion started by: pko60
1 Replies

2. Filesystems, Disks and Memory

Adding RAID to server

Hi, I have a server that I am adding a RAID that we purchased to. The server works fine. It is running Fedora 7 and is a Dell Precision 690. When the RAID is attached, it boots up and says the following: Controller Bus #00, Device#1F, Function#02: 00 Ports No device found AHCI BIOS not... (0 Replies)
Discussion started by: user23
0 Replies

3. Red Hat

linux server with raid controller card

I am planning on building a fedora box with raid controller (database server). Is anybody done that ? also what kind of software do you need to backup and recover data. (1 Reply)
Discussion started by: amir07
1 Replies

4. UNIX for Dummies Questions & Answers

efficient raid file server

I need to put together a RAID1 file server for use by Windoze systems. I've built zillions of windows systems from components. I was a HPUX SE for a long time at HP, but have been out of the game for years. I've got an old workhorse mobo FIC PA-2013 with a 450 MHz K6 III+ I could use, but I'd... (2 Replies)
Discussion started by: pcmacd
2 Replies

5. Hardware

Hardware RAID on Sun T2000 Server

Hi All I have a Sun T2000 server. Couple of years ago I had configured and mirrored the boot drive with an other drive using hardware RAID 1 using raidctl command. Following is the hardware RAID output. root@oracledatabaseserver / $ raidctl RAID Volume RAID RAID Disk... (0 Replies)
Discussion started by: Tirmazi
0 Replies

6. Hardware

Raid 0 on database server

Hi guys. if we want to use SSD drives on a database server, can we use RAID 0 configuration because of their reliability? (3 Replies)
Discussion started by: majid.merkava
3 Replies

7. Linux

Help Setting up Linux Raid Server

I just built a home computer with 3TB hard drives I wanted to set up in a RAID 5 and load Ubuntu server onto it. The first thing I did was set up the drives in a RAID 5 using just the motherboard chipset software to do it, so a 'hardware' RAID basically. I installed Windows first to see if... (2 Replies)
Discussion started by: lorewap3
2 Replies

8. Filesystems, Disks and Memory

Help finding a Unix friendly RAID 1 backup

First time poster and a very new Unix user, so I'll just pre-apologize for stupid questions now. Does anybody know of a good RAID 1 hard drive backup that is Unix friendly? I want to avoid any hardcore programming. Can you recommend both NAS and non-NAS options? I need to do nightly backups... (31 Replies)
Discussion started by: c.wakeman
31 Replies

9. Hardware

3ware RAID server

We have a 3ware RAID server at work, and as the appointed systems administrator (by virtue of being the one with the most knowledge) I've taken on the job of maintaining it. I've installed smartmontools on it to keep an eye on the drives and run scans every day, and looking at the data from the... (0 Replies)
Discussion started by: Krendoshazin
0 Replies
YAFAPPLICATION(3)							 1							 YAFAPPLICATION(3)

The YafApplication class

INTRODUCTION
Yaf_Application provides a bootstrapping facility for applications which provides reusable resources, common- and module-based bootstrap classes and dependency checking. Note Yaf_Application implements the singleton pattern, and Yaf_Application can not be serialized or unserialized which will cause problem when you try to use PHPUnit to write some test case for Yaf. You may use @backupGlobals annotation of PHPUnit to control the backup and restore operations for global variables. thus can solve this problem. CLASS SYNOPSIS
Yaf_Application final Yaf_Application Properties o protected$config o protected$dispatcher o protectedstatic$_app o protected$_modules o protected$_running o protected$_environ Methods o publicstatic void Yaf_Application::app (void ) o public void Yaf_Application::bootstrap ([Yaf_Bootstrap_Abstract $bootstrap]) o public Yaf_Application Yaf_Application::clearLastError (void ) o private void Yaf_Application::__clone (void ) o public Yaf_Application::__construct (mixed $config, [string $envrion]) o public void Yaf_Application::__destruct (void ) o public void Yaf_Application::environ (void ) o public void Yaf_Application::execute (callable $entry, string $...) o public Yaf_Application Yaf_Application::getAppDirectory (void ) o public Yaf_Config_Abstract Yaf_Application::getConfig (void ) o public Yaf_Dispatcher Yaf_Application::getDispatcher (void ) o public string Yaf_Application::getLastErrorMsg (void ) o public int Yaf_Application::getLastErrorNo (void ) o public array Yaf_Application::getModules (void ) o public void Yaf_Application::run (void ) o public Yaf_Application Yaf_Application::setAppDirectory (string $directory) o private void Yaf_Application::__sleep (void ) o private void Yaf_Application::__wakeup (void ) PROPERTIES
o $config - o $dispatcher - o $_app - o $_modules - o $_running - o $_environ - PHP Documentation Group YAFAPPLICATION(3)
All times are GMT -4. The time now is 01:10 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy