cfgadm_sysctrl(1M)														cfgadm_sysctrl(1M)

NAME

       cfgadm_sysctrl - EXX00 system board administration

SYNOPSIS

       /usr/sbin/cfgadm -c function [-f] [-o disable-at-boot | enable-at-boot] [-n | -y] sysctrl0:slot# ...

       /usr/sbin/cfgadm -x quiesce-test sysctrl0:slot#

       /usr/sbin/cfgadm -x insert-test | remove-test sysctrl0:slot# ...

       /usr/sbin/cfgadm -x set-condition-test=# sysctrl0:slot# ...

       /usr/sbin/cfgadm [-l] -o disable-at-boot | enable-at-boot sysctrl0:slot# ...

       The  sysctrl  hardware specific library /usr/platform/sun4u/lib/cfgadm/sysctrl.so.1 provides dynamic reconfiguration functionality for con-
       figuring and disconnecting system boards on E6X00, E5X00, E4X00, and E3X00 systems. You can insert both I/O and CPU boards into a slot on a
       running	system	that  is  configured for Solaris without rebooting. You can also disconnect and remove both types of boards from a running
       system without rebooting.

       System slots appear as attachment points in the device tree, one attachment point for each actual slot in the system chassis. If a board is
       not  in	a  slot,  the receptacle state is empty. If a board is powered-off and ready to remove, the receptacle state is disconnected. If a
       board is powered-on and is connected to the system bus, the receptacle state is connected.

	The occupant state is unconfigured when the receptacle state is empty or disconnected. The occupant state is either unconfigured  or  con-
       figured when the receptacle state is connected.

       In  the	configured  state the devices on a board are available for use by Solaris. In the unconfigured state, the devices on the board are
       not.

       Inserting a board changes the receptacle state from empty to disconnected. Removing a board changes the receptacle state from  disconnected
       to empty. Removing a board that is in the connected state crashes the operating system and can result in permanent damage to the system.

       Refer to cfgadm(1M) for a more complete description options.

       The following options are supported:

       -c function

	   Perform the state change function. Specify function as connect, disconnect, configure or unconfigure.

	   configure

	       Change the occupant state to configure.

	       If  the	receptacle  state is disconnected, the configure function first attempts to connect the receptacle. The configure function
	       walks the OBP device tree created as part of the connect function and creates the Solaris device tree nodes, attaching  devices	as
	       required. For CPU/Memory boards, configure adds CPUs to the CPU list in the powered-off state. These are visible to the psrinfo(1M)
	       and psradm(1M) commands. Two memory attachment points are published for CPU/memory boards. Use mount(1M) andifconfig(1M) to use I/O
	       devices	on  the  new  board. To use CPUs, use psradm -n to on-line the new processors. Use cfgadm_ac(1M) to test and configure the
	       memory banks.

	   connect

	       Change the receptacle state to connected.

	       Changing the receptacle state requires that the system bus be frozen while the bus signals are connected and the board tested.  The
	       bus  is frozen by running a quiesce operation which stops all process activity and suspends all drivers. Because the quiesce opera-
	       tion and the subsequent resume can be time consuming, and are not supported by all drivers, the -x quiesce-test is provided.  While
	       the  system  bus is frozen, the board being connected is tested by firmware. This operation takes a short time for I/O boards and a
	       significant time for CPU/Memory boards due to CPU external cache testing. This  does  not  provide  memory  testing.  The  user	is
	       prompted for confirmation before proceeding with the quiesce. Use the -y or -n option to override the prompt. The connect operation
	       is refused if the board is marked as disabled-at-boot, unless either the force flag, -f, or the enable at boot flag, -o	enable-at-
	       boot, is given. See -l.

	   disconnect

		Change the receptacle state to disconnected.

	       If  the	occupant  state is configure, the disconnect function first attempts to unconfigure the occupant. The disconnect operation
	       does not require a quiesce operation and operates quickly. The board is powered-off ready for removal.

	   unconfigure

	       Change the occupant state to unconfigureed.

	       Devices on the board are made invisible to Solaris during this process. The I/O devices on  an  I/O  board  are	removed  from  the
	       Solaris device tree. Any device that is still in use stops the unconfigure process and be reported as in use. The unconfigure oper-
	       ation must be retried after the device is made non-busy. For CPU/Memory boards, the memory must have been changed to the  unconfig-
	       ured  state prior to issuing the board unconfigure operation. The CPUs on the board are off-lined, powered off and removed from the
	       Solaris CPU list.  CPUs	that  have  processes  bound  to  them	cannot	be  off-lined.	See  psradm(1M),  psrinfo(1M),	pbind(1M),
	       andp_online(2) for more information on off-lining CPUs.

       -f

	    Force  a  block  on  connecting  a	board  marked  as  disabled-at-boot in the non-volatile disabled-board-list variable. See Platform
	   Notes:Sun Enterprise 6x00/5x00/4x00/3x00 Systems

       -l

	   List options. Supported as described in cfgadm(1M)cfgadm(1M).

	   The type field can be one of cpu/mem, mem, dual-sbus, sbus-upa, dual-pci, soc+sbus, soc+upa, disk or unknown.

	   The hardware-specific info field is set as follows: [disabled at boot] [non-detachable] [100 MHz capable]

	   For sbus-upa and soc+upa type boards, the following additional information appears first: [single buffered ffb|double  buffered  ffb|no
	   ffb installed] For disk type boards, the following additional information appears first: {target: # | no disk} {target: # | no disk}

       -o disable-at-boot | enable-at-boot

	   Modify  the	state of the non--volatile  disabled-board-list variable. Use this the -o option in conjunction with the -c function or -l
	   option.

	   Use -o enable-at-boot with the -c connect to override a block on connecting a disabled-at-boot board.

       -x insert-test | remove-test

	   Perform a test.

	    Specify remove-test to change the driver state for the specified slot from disconnected to	empty  without	the  need  for	physically
	   removing the board during automated test sequences.

	   Specify  insert-test  to change the driver state of a slot made to appear empty using the remove-test command to the disconnected state
	   as if it had been inserted.

       -x quiesce-test sysctrl0:slot1

	   Perform a test.

	   Allows the quiesce operation required for board connect operations to be exercised. The execution of this test confirms that, with  the
	   current  software and hardware configuration, it is possible to quiesce the system. If a device or process cannot be quiesced, its name
	   is printed in an error message. Any valid board attachment point can be used with this command, but since all systems have a slot1  the
	   given form is recommended.

       -x set-condition-test=#

	   Perform a test.

	   Allows  the condition of a system board attachment point to be set for testing the policy logic for state change commands. The new set-
	   ting is given as a number indicating one of the following condition values:

	   0	  unknown
	   1	  ok
	   2	  failing
	   3	  failed
	   4	  unusable

OPERANDS

       The following operand is supported:

       sysctrl0:slot#	       The attachment points for boards on EXX00 systems are published by instance 0 of the sysctrl driver (sysctrl0). The
			       names  of  the  attachment  points  are numbered from slot0 through slot15. Specify # as a number between 0 and 15,
			       indicating the slot number. This form conforms to the logical ap_id specification given in cfgadm(1M).  The  corre-
			       sponding physical ap_ids are listed in the FILES section.

       /usr/platform/sun4u/lib/cfgadm/sysctrl.so.1

	   Hardware specific library

       /devices/central@1f,0/fhc@0,f8800000/clock-board@0,900000:slot*

	   Attachment Points

       See attributes(5) for descriptions of the following attributes:

       +-----------------------------+-----------------------------+
       |      ATTRIBUTE TYPE	     |	    ATTRIBUTE VALUE	   |
       +-----------------------------+-----------------------------+
       |Availability		     |SUNWkvm.u 		   |
       +-----------------------------+-----------------------------+

       cfgadm(1M), cfgadm_ac(1M), ifconfig(1M), mount(1M),  pbind(1M), psradm(1M), , psrinfo(1M), config_admin(3CFGADM), attributes(5)

       Sun Enterprise 6x00, 5x00, 4x00 and 3x00 Systems Dynamic Reconfiguration User's Guide

       Platform Notes:Sun Enterprise 6x00/5x00/4x00/3x00 Systems

NOTES

       Refer to the Sun Enterprise 6x00, 5x00, 4x00 and 3x00 Systems Dynamic Reconfiguration User's Guide for additional details regarding dynamic
       reconfiguration of EXX00 system CPU/Memory boards.

								    10 Mar 1999 						cfgadm_sysctrl(1M)