09-18-2015
Thank for reply Hickd8
In my setup , I am using T5240 server as storage using iscsitadm command creating LUNs & T2000 server as two nodes.
For you information, amity user is used by my real brother & we both are working on the same issue
8 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hello agian !
What is the difference between SCSI and IDE hard disks ?
I have Intel PC and when i check i have Generic IDE TYPE DISK0
is IDE hard disk is ok for Solrais ? or should i buy the SCSI hard disk ?
Thanks
Abid Malik (3 Replies)
Discussion started by: abidmalik
3 Replies
2. AIX
Hi
Is it possible to install in p5 and pSeries SCSI Disks from SUN on DELL? Will they work?
Regards,
Pit (0 Replies)
Discussion started by: piooooter
0 Replies
3. Solaris
First time writer....take it easy on me.
I had a situation where I lost all paths to EMC disk. There was a failure on the EMC frame. After that was repaired, my server had a difficult time reclaiming all disks and veritas had marked the disks as failed. Veritas was confused. What are some of... (3 Replies)
Discussion started by: Sowser
3 Replies
4. Linux
Hi,
I am installing perl and rsnapshot on the OS of a Western Digital MyBook disk.
To install perl the ./Configure command tells me that both 'tr' and 'split' are missing. I don't find them on the net.
Where can I download them?
Thanks.
Charles. (2 Replies)
Discussion started by: mosndup
2 Replies
5. Solaris
Yesterday my customer told me to expect a vcs upgrade to happen in the future. He also plans to stop using HDS and move to EMC.
Am thinking how to migrate to sun cluster setup instead.
My plan as follows leave the existing vcs intact as a fallback plan.
Then install and build suncluster on... (5 Replies)
Discussion started by: sparcguy
5 Replies
6. Solaris
Hello experts -
I am planning to install a Sun cluster 4.0 zone cluster fail-over. few basic doubts.
(1) Where should i install the cluster s/w binaries ?. ( global zone or the container zone where i am planning to install the zone fail-over)
(2) Or should i perform the installation on... (0 Replies)
Discussion started by: NVA
0 Replies
7. Solaris
Hi All,
I am a RH Linux admin that recently started working at a company with a number of SUN Servers so it's been an interesting transition.
Considering the last person left with very little documentation left behind so I have been picking up most issues half complete, or troubleshot.
... (7 Replies)
Discussion started by: MobileGSP
7 Replies
8. HP-UX
Hi guys,
I need some help to better understand how to determine if a disk have persistent SCSI reservation. I know that we should use the "Persisten Reservation Utility" but we are not allowed to run that tool. Since we have the output from some grab utility and specifically we have the... (0 Replies)
Discussion started by: cecco16
0 Replies
LEARN ABOUT CENTOS
scsi-rescan
RESCAN-SCSI-BUS.SH(1) User Commands RESCAN-SCSI-BUS.SH(1)
NAME
rescan-scsi-bus.sh - script for adding and removing SCSI devices without rebooting
SYNOPSIS
rescan-scsi-bus.sh [options] [host [host ...]]
OPTIONS
-a, --alltargets
scan all targets, not just currently existing [default: disabled]
-d enable debug [default: 0]
-l activates scanning for LUNs 0--7 [default: 0]
-L NUM activates scanning for LUNs 0--NUM [default: 0]
-w, --wide
scan for target device IDs 0--15 [default: 0--7]
-c enables scanning of channels 0 1 [default: 0 / all detected ones]
-r, --remove
enables removing of devices [default: disabled]
-f, --flush
flush failed multipath devices [default: disabled]
-i, --issue-lip
issue a FibreChannel LIP reset [default: disabled]
-u, --update
look for existing disks that have been remapped
-s, --resize
look for resized disks and reload associated multipath devices, if applicable
--forcerescan
rescan existing devices
--forceremove
remove and readd every device (DANGEROUS)
--nooptscan
don't stop looking for LUNs is 0 is not found
--color
use coloured prefixes OLD/NEW/DEL
--hosts=LIST
scan only host(s) in LIST
--channels=LIST
scan only channel(s) in LIST
--ids=LIST
scan only target ID(s) in LIST
--luns=LIST
scan only lun(s) in LIST
--sync, --nosync
issue a sync / no sync [default: sync if remove]
--attachpq3
tell kernel to attach sg to LUN 0 that reports PQ=3
--reportlun2
tell kernel to try REPORT_LUN even on SCSI2 devices
--largelun
tell kernel to support LUNs > 7 even on SCSI2 devs
--sparselun
tell kernel to support sparse LUN numbering
Host numbers may thus be specified either directly on cmd line (deprecated) or or with the --hosts=LIST parameter (recommended).
LIST: A[-B][,C[-D]]... is a comma separated list of single values and ranges (No spaces allowed.)
SEE ALSO
rescan-scsi-bus.sh Homepage: http://www.garloff.de/kurt/linux/#rescan-scsi
sg3_utils Homepage: http://sg.danny.cz/sg
rescan-scsi-bus.sh 1.57 leden 2014 RESCAN-SCSI-BUS.SH(1)