09-14-2015
Moderator's Comments:
|
|
Continued refusal to used CODE tags as required by forum rules will lead to you being banned from this site.
Do Not expect the volunteers trying to help you here to respond to your posts immediately. Bumping up posts isn't allowed either.
You have been placed in read-only mode for one day. Please use this time to review the rules you agreed to when you joined this forum.
|
|
This User Gave Thanks to Don Cragun For This Post:
10 More Discussions You Might Find Interesting
1. Ubuntu
I have a Ubuntu linux (Ubuntu 6.06) at home. I have a ADSL modem (eth0) connected to it for my Broadband connection. It all works fine when the system gets started. But, when I receive a call, the link goes off. And then I lose my internet connection. I tried ifup/ifdown to bring the connection... (2 Replies)
Discussion started by: ranj@chn
2 Replies
2. Solaris
Hi guys,
I got a global zone with with two zones runnig.
After a patch upgrade (July 2010) one of them stop to working fine: basically I can't ping it ( I mean I can ping from the other zone, but actually the ping pass across the global zone..) and I can't access it in ssh or telnet...(actually... (0 Replies)
Discussion started by: cecco16
0 Replies
3. Red Hat
Hi, I'm trying to create a lab environment in my personal laptop. I have created a virtualbox RHEL6.1 and I want to make another copy out of it to make it 4 instances by simply copying the whole folder and changing their name and then changing their IP addresses. is this OK? please advice.
for... (2 Replies)
Discussion started by: messi777
2 Replies
4. IP Networking
Hello,
I am trying to set up Channel Bonding on a RHEL6 Virtual Box VM. I have 2 ethernet cards on the machine which are set up in Internal Network mode. I followed all the steps exactly as mentioned in the RHEL6 deployment Guide, but for some reason i think results are not correct. Here are my... (13 Replies)
Discussion started by: Rohit Bhanot
13 Replies
5. Red Hat
Hi team,
I'm running into a problem configuring bonding on an CentOS 64bit on DELL Server. I'm connecting eth0 and eth1
to a Cisco 2948 (CatOS 8.1(3)) and receiving flapping notices. The
ethernet address is that of the primary interface. I have tried
several different modes,... (3 Replies)
Discussion started by: leo_ultra_leo
3 Replies
6. IP Networking
HI all,
First post on the forum, and my first proper project on the Paspberry Pi, so sorry if this is in the wrong place.
I am trying to turn my Pi in to a 3G/4G Bonding router. I have been researching and trying this for a week or so now. The basic plan is to have up to 6 ZTE MF823 USB... (0 Replies)
Discussion started by: elliottlc
0 Replies
7. Red Hat
We have two hosts in same vlan with same route rules.
One of them is not able to connect to an outside IP while in another I get "failed: Connection timed out" while testing the connectivity through netcat.
I have tried mtr /traceroute and it gives me the same results.
Is there a netcat... (1 Reply)
Discussion started by: jacki
1 Replies
8. Red Hat
Dear All ,
Very recently we have configured Network bonding in our Linux Server Redhat Linux 5.x.
After configuring , we restarted the network services , the link was down after that , we could not login in to the Server.
So after that , we logged in to console and tried to... (2 Replies)
Discussion started by: jegaraman
2 Replies
9. Linux
Respected Members,
We encountered an issue during node reboot when eth1 and eth5 of bond1 were behaving unusual(both eth1 and eth5 were in unknown states and ifdown and ifup were used to rectify). Please find the messages and configuration files as below and please let me know for any other... (0 Replies)
Discussion started by: Mudit Bansal
0 Replies
10. UNIX for Beginners Questions & Answers
bond0 active in eth0 and inactive in eth4. why eth4 received network package?
Bonding Mode: fault-tolerance (active-backup)
Primary Slave: eth0 (primary_reselect failure)
Currently Active Slave: eth0
MII Status: up
MII Polling Interval (ms): 100
Up Delay (ms): 0
Down Delay (ms): 0
... (4 Replies)
Discussion started by: samran35
4 Replies
EPAIR(4) BSD Kernel Interfaces Manual EPAIR(4)
NAME
epair -- A pair of virtual back-to-back connected Ethernet interfaces.
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device epair
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_epair_load="YES"
DESCRIPTION
The epair is a pair of Ethernet-like software interfaces, which are connected back-to-back with a virtual cross-over cable.
Each epair interface pair is created at runtime using interface cloning. This is most easily done with the ifconfig(8) create command or
using the cloned_interfaces variable in rc.conf(5). While for cloning you only give either epair or epair<n> the epair pair will be named
like epair<n>[ab]. This means the names of the first epair interfaces will be epair0a and epair0b.
Like any other Ethernet interface, an epair needs to have a network address. Each epair will be assigned a locally administered address by
default, that is only guaranteed to be unique within one network stack. To change the default addresses one may use the SIOCSIFADDR ioctl(2)
or ifconfig(8) utility.
The basic intend is to provide connectivity between two virtual network stack instances. When connected to a if_bridge(4) one end of the
interface pair can also be part of another (virtual) LAN. As with any other Ethernet interface one can configure vlan(4) support on top of
it.
SEE ALSO
ioctl(2), altq(4), bpf(4), if_bridge(4), vlan(4), loader.conf(5,) rc.conf(5), ifconfig(8)
HISTORY
The epair interface first appeared in FreeBSD 8.0.
AUTHORS
The epair interface was written by Bjoern A. Zeeb, CK Software GmbH, under sponsorship from the FreeBSD Foundation.
BSD
July 26, 2009 BSD