Node: NODE-B State: UP
Interface: NODE-B_STBY (0) Address: 10.x.x.x
State: UP
Interface: NODE-B_B (0) Address: 10.x.x.x
State: UP
Interface: NODE-B-CI (0) Address: 10.x.x.x
State: UP
Resource Group: RG02_Sapvg State: On line
Node: NODE-A State: DOWN
Interface: NODE-A_STBY (0) Address: 10.x.x.x
State: DOWN
Interface: NODE-A_B (0) Address: 10.x.x.x
State: DOWN
====clstat output from node A ====
Code:
Node: NODE-B State: DOWN
Node: NODE-A State: UP
========================
I have done cluster verification and sync. No error was triggered on that and it completed normally. i have stop and started the cluster services but same issue.
Moderator's Comments:
edit by bakunin: could you please use CODE-tags, as you have been asked to do? Thank you!
I am trying to set up a two host cluster. trouble is with the cluster transport configuration.
i'm using e1000g2 and g3 for the cluster transport. global0 and global1 are my two nodes, and I am running the scinstall from global1.
i think i should be expecting, is this:
The following... (19 Replies)
Hello,
As explained, I've encountered an issue while installing Solaris 10 SPARC Recommended Patch Cluster (2009.10.23).
Actually, patch no 120011-14 stops with the following error:
ERROR: attribute verification of </var/run/.patchSafeMode/root/usr/bin/passwd> failed
file type <f>... (6 Replies)
Yesterday my customer told me to expect a vcs upgrade to happen in the future. He also plans to stop using HDS and move to EMC.
Am thinking how to migrate to sun cluster setup instead.
My plan as follows leave the existing vcs intact as a fallback plan.
Then install and build suncluster on... (5 Replies)
I am using VMware Workstation-7 on Windows-XP host .
I am trying to configure Solaris 10-X86 guest os based 2 nodes Sun Cluster .
I have added one extra Virtual Lan adapter on my VMware with another subnet (that I would like to put for SUN Cluster private communication).
I have... (0 Replies)
I have installed sun cluster 3.2 on two sprac servers. Configured a failover resource group. Added a LogicalHostname resource to it. LogicalHostname is also added to /etc/hosts with ip address.
I am able to access cluster by share ip used for logical hostname but when i try to switch the resource... (0 Replies)
Hello experts -
I am planning to install a Sun cluster 4.0 zone cluster fail-over. few basic doubts.
(1) Where should i install the cluster s/w binaries ?. ( global zone or the container zone where i am planning to install the zone fail-over)
(2) Or should i perform the installation on... (0 Replies)
Hello everyone,
I have two Solaris 10 servers that are on cluster. The cluster is a Sun Cluster 3.2
I have a script cronned that stop/start a ressource in a resource group everyday.
Today I have checked the status of the ressources and I found that my ressource group have a "Error--stop... (1 Reply)
Hi Guys,
I am not much aware of clusters but i have few questions can someone provide the overview as it would be very helpful for me.
How can i perform cluster failover test to see all the services are failing back to other node ? If it is using veritas cluster then what kind of... (2 Replies)
Hi all,
Few hours ago I did some changes in our Solaris cluster servers. Below are changes I did :
1. Installed latest Solaris 10 patchset from oracle.
2. Enabled BSM log module. Entered into single user mode and rebooted. After reboot changed to multi-user mode and rebooted again.
Now... (7 Replies)
09-09-2015
