It is a typical mistake from My side.Data Bit should be 8 instead of 9.
I need the commands to do so.
Oh, thank goodness -- that's much, much easier.
Quote:
To set the following I have used the following command.
If you see again the parameter by the following command, it shows the attibute as set by the above command.
Do I need to restart the machine after that?
You do not.
Indeed, if you do, you'll have to set it again. Remember that -- you might want to put it in local.start or in an @reboot cron job.
wisecracker speaks wisely. UNIX serial ports have far more settings than data bits and flow control. See Canonical and noncanonical mode in man termios. What you need depends on the needs of your application (reading lines of text? canonical. reading individual bytes of binary data? raw.)
I am having trouble with a device connected through a serial port on my sun workstation ( I am running solaris 7).
The seriel device works on an identical workstation running the same o/s version but when I move it to the initial workstation it doesn't work. I am using an rs232 serial cable and... (1 Reply)
I have a serial modem connected to a usb port using an adapter cable. The system is a HP DL360. RedHat ES3.0
I am using the device /dev/ttyUSB0
When I issue the command "mgetty ttyUSB0" I get the following output in the log file.
How do I get the system to see the modem.
12/02 14:17:55... (2 Replies)
Hi
I have just re-installed Compaq ML350 G2 Server with Unix SCO 5.0.5 and
informix DBMS .
on this server we have 2 serial ports , unfortunately its not working.
Can anyone help me to check the serial ports working or not OR guide me
to reconfigure it.
I have attached a device with... (1 Reply)
I am developing an application in c with Linux OS, where a radio modem working at baud rate 9600 will be attached to PC on serial port. More than four such units will be communicating at one time, so there may be jamming or data corruption. Each module will be transmitting Data packets less than... (2 Replies)
I am working with solaris 9 sparc and I want to connect physical device in serial port but when I am connecting it,It is showing the error window saying--
So can any1 tell me the reason or is there any package I have to add to work with serial port??? (2 Replies)
Hi,
I am working with Sun Solaris 9 Sparc,Sun-Blade-100.In my application,I need to monitor the UPS using Serial port.
When I am using JRE 1.4 in my application,I am able to monitor it but when I am upgrading the JRE version from 1.4 to JRE1.6. I am not able to monitor the UPS.It is showing the... (1 Reply)
Hi,
I have a external board connected to my serial port. I need to execute "shutdown -r now" command when system boot up. When system boots up it requires a username ans password. Then I need to run my command. I can use rc script but that is rebooting system before it asks for username and... (0 Replies)
Hi Everyone,
In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected... (3 Replies)
Hello,
I have an unloaded T5140 machine and want to access the ILOM for the first time and subsequently the network port after that., and then load Solaris 10 the final January 2011 build.
The first part is what confuses me -the cabling.
I am coming from a Windows machine (w/appropriate... (5 Replies)
I am trying to change the setting of serial port baud rate in Red Hat Linux 5.9 by the following command.
>> stty 9600 cs8 -parenb -ixon -cstopb -echo -F /dev/ttyS0
The serial port will be used by our custom application in 2 separate servers which are the replica of one another.
The port setting... (2 Replies)
Discussion started by: Anjan Ganguly
2 Replies
LEARN ABOUT CENTOS
nsd-xfer
nsd-xfer(8) nsd 3.2.12 nsd-xfer(8)NAME
nsd-xfer - AXFR client to transfer zones from a name server
SYNOPSIS
nsd-xfer [-4] [-6] [-a address[@port]] [-p port] [-s serial] [-T tsiginfo] [-v] -z zone -f file servers
DESCRIPTION
Nsd-xfer is program to transfer zones from a name server using AXFR. NSD is a complete implementation of an authoritative DNS nameserver.
OPTIONS -4 Only send to IPv4 addresses.
-6 Only send to IPv6 addresses.
-a address[@port]
Specify the source address (and port) to send from.
-f file
The file to store the zone in.
-p port
Specify the port to send to.
-s serial
Specify the serial of the current zone. The zone is only transferred if the master server has a zone with a greater serial number.
-T tsiginfo
Use TSIG to verify the zone transfer. The tsiginfo file must contain the TSIG key information. The file is removed upon successful
reading of the key. The format of the tsiginfo file is described in the doc/README file (section 3.3).
-v Be more verbose.
-z zone
Specify the zone to receive.
servers
List of nameservers to try.
EXAMPLES
To run this program the standard way type:
# nsd-xfer -z foobar.cz -f foobar.cz.zone 1.2.3.4
SEE ALSO nsd(8), nsdc(8), nsd.conf(5), nsd-checkconf(8), nsd-notify(8), nsd-patch(8), zonec(8)AUTHORS
NSD was written by NLnet Labs and RIPE NCC joint team. Please see CREDITS file in the distribution for further details.
NLnet Labs jul 19, 2012 nsd-xfer(8)