Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: Cstm and gsp conflict on power status
Operating Systems HP-UX Cstm and gsp conflict on power status Post 302953701 by port43 on Monday 31st of August 2015 11:55:54 AM
Old 08-31-2015
Cstm and gsp conflict on power status
Hello all,
I have a case where the power supply in slot 1 was replaced last week as it had failed. Prior to that it was showing failed in cstm:
Code:
Cabinet 0 Hardware Inventory:
   Component                        Present   Failure    State
   ---------                        -------   -------   -------
   Cabinet Fans (blowers)               8         0     unknown
   Cabinet Power Supplies               3         1     unknown
   I/O Power Supplies                   0
   BackPlane Power Supplies             0

   unknown - Firmware is unable to determine the state of the hardware.

Cabinet 0 Slot Locations:
                   Hardware Component Map (locations 00-31)
       -----------------------------------------------------------------
       |0|0|0|0|0|0|0|0|0|0|1|1|1|1|1|1|1|1|1|1|2|2|2|2|2|2|2|2|2|2|3|3|
       |0|1|2|3|4|5|6|7|8|9|0|1|2|3|4|5|6|7|8|9|0|1|2|3|4|5|6|7|8|9|0|1|
       |-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|
cf(b)  |p|p|p|p|p|p|p|p| | | | | | | | | | | | | | | | | | | | | | | | |
cps    |p|F|p| | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
       -----------------------------------------------------------------
       s - Slot available for the hardware component.
       p - Component present at the marked location.
       F - Component failed at the marked location.
cf(b)- Cabinet Fan (blower)
cps  - Cabinet Power Supply

as well as from the GSP:
Code:
GSP> ps
PS
Power Monitor Status:
Firmware Revision : 3
System Power state: On            Power Switch      : On         
Temperature       : Normal        Selected fan state: Normal      

          Power supplies          |  Fan                          
 #  State          Type           |  States        
-----------------------------------------------------------
0  Normal          Type 0         | Normal         
1  Fault           Type 0         | Normal        
2  Normal          Type 0         | Normal         
3    -                -           | Normal        
4    -                -           | Normal        
5    -                -           | Normal         
6    -                -           | Normal         
7    -                -           | Normal

After the replacement (the server has since been rebooted), the GSP shows slot 1 as normal:
Code:
GSP> ps
PS
Power Monitor Status:
Firmware Revision : 3
System Power state: On            Power Switch      : On
Temperature       : Normal        Selected fan state: Normal

          Power supplies          |  Fan
 #  State          Type           |  States
-----------------------------------------------------------
0  Normal          Type 0         | Normal
1  Normal          Type 0         | Normal
2  Normal          Type 0         | Normal
3    -                -           | Normal
4    -                -           | Normal
5    -                -           | Normal
6    -                -           | Normal
7    -                -           | Normal

but cstm still shows slot 1 as failed:
Code:
Cabinet 0

Cabinet 0 Hardware Inventory:
   Component                        Present   Failure    State
   ---------                        -------   -------   -------
   Cabinet Fans (blowers)               8         0     unknown
   Cabinet Power Supplies               3         1     unknown
   I/O Power Supplies                   0
   BackPlane Power Supplies             0

   unknown - Firmware is unable to determine the state of the hardware.

Cabinet 0 Slot Locations:
                   Hardware Component Map (locations 00-31)
       -----------------------------------------------------------------
       |0|0|0|0|0|0|0|0|0|0|1|1|1|1|1|1|1|1|1|1|2|2|2|2|2|2|2|2|2|2|3|3|
       |0|1|2|3|4|5|6|7|8|9|0|1|2|3|4|5|6|7|8|9|0|1|2|3|4|5|6|7|8|9|0|1|
       |-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|
cf(b)  |p|p|p|p|p|p|p|p| | | | | | | | | | | | | | | | | | | | | | | | |
cps    |p|F|p| | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
       -----------------------------------------------------------------
       s - Slot available for the hardware component.
       p - Component present at the marked location.
       F - Component failed at the marked location.
cf(b)- Cabinet Fan (blower)
cps  - Cabinet Power Supply

What am I supposed to clear to correct this conflict?

Thank you for your attention.
 

7 More Discussions You Might Find Interesting

1. HP-UX

How to use CSTM on HP-Ux 11i V2

Hi, Newbie here......I am an new guy on HP-Ux... may i ask all the the guru's and who has eperienced here to enlightened me on how to use the CSTM command. My goal is to view the current HW installed on the Server. Thanks in advance. (1 Reply)
Discussion started by: renobal
1 Replies

2. Red Hat

power supply status in sysreport

Hello guys: I'm a beginner in this exciting world of open spource and linux. I'm working as a support engineer and a customer send back to me a sysreport from his system running redhat 4. the customer has a power supply failed in his server and to see it and justify the replacement I required a... (0 Replies)
Discussion started by: amani
0 Replies

3. HP-UX

Conflict between df -k and du -sk...again

Hi, I know this has been discussed a number of time but i could not get the exact answer. So need help again. Issue: The two command for same file system shows different size. du -sk shows toatl size is 12780685 KB while df -k 45289229 used allocated Kb /oxt/mantran/bin $ du -sk... (8 Replies)
Discussion started by: malaya_17
8 Replies

4. Solaris

Solaris 9 IP conflict

Hi Gurus I am in a strange situation. I have a SUN sparc server . The server was having an IP say X..... (this IP X is now being used by another server)..... I have just installed fresh solaris 9 OS on the same server and given new IP say Y. I also configured probe based IPMP with ce0 and... (2 Replies)
Discussion started by: ningy
2 Replies

5. HP-UX

echo "selall;info;wait;infolog" | /usr/sbin/cstm problem

Hello, On a HP-UX 10.20 server I've executed something similar to this command: # echo 'selall;info;wait;infolog;view;done' | /usr/sbin/cstm But it returns sometype of "argument list too long" error. I suppose there is a way to fix it by using xargs but I can't figure it out. Any... (7 Replies)
Discussion started by: asanchez
7 Replies

6. AIX

Finding Power Supply Status

Hi, As in Management Modules of IBM it is possible to find out wheather out of dual powersupply , if one goes down. is it possible to find out in HMC to find out if one power supply goes down of P Series server? if server is remotely HOw to find out if one power supply of server is down?... (1 Reply)
Discussion started by: manoj.solaris
1 Replies

7. Shell Programming and Scripting

Conflict with the operator in IF

I am using a script like this source=$1 if ; then echo "got it" else echo "lost it" fi But the script is giving th error like script.ksh: ==: unknown test operator Can i know , is the syntax iam using is correct or suggest me a good way. ... (3 Replies)
Discussion started by: nani1984
3 Replies
All times are GMT -4. The time now is 02:48 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy