08-28-2015
I realize this might be a really dumb thing to say but have you checked all the BIOS settings with one of your good machines? Especially the network interface settings in the Advanced section.
Also, perhaps try a Linux (or similar) 'live CD/DVD' to test that the network interface is not hardware faulty.
Apologies if that sounds too obvious.
9 More Discussions You Might Find Interesting
1. Solaris
Hi,
I build a jumpstart server with a running dhcp server. I already managed to install a x86 client via network. But my sparc clients aren't still working.
When booting via network I get the following message:
Timeout waiting for ARP/RARP packet
I ran "snoop" on the server:
client2 ->... (1 Reply)
Discussion started by: Jay_Fisi
1 Replies
2. Solaris
I just built a jumpstart server on a Solaris 9 sun box and have had no problems jumpstarting other sol9 boxes using the custom rules. I've also copied a Solaris 10 image onto that same solaris 9 server and have had problems loading Solaris 10. These boxes will go directly to the manual OS install... (5 Replies)
Discussion started by: salty
5 Replies
3. Solaris
Hi all ,
I am trying to jumpstart ( webstart) solaris 9 on E2900 ( client) using the DVD of a V440 server ( jumstart server). I did the setup for the V440 as follows :
cleaning up preexisting install client "XXXXXXX"
removing XXXXXXXfrom bootparams
removing /etc/bootparams, since it is... (14 Replies)
Discussion started by: ppass
14 Replies
4. Solaris
I need a little help figuring out why my custom jumpstart network installation is dumping me to a manual install.
I am trying to install Solaris 10 (unattended) over the wire from my jumpstart server to an HP Proliant DL380 server but I'm having difficulties with the unattended part.
So, what... (2 Replies)
Discussion started by: alias.256
2 Replies
5. Solaris
Hi All
I have a Solaris 10 jumpstart boot/config server set up on a subnet, and am trying to use it to build a client (the only other machine on the network). Things start out just fine, with the client booting into the Solaris Installation program, but then it just coredumps just as it's... (4 Replies)
Discussion started by: rickedwards44
4 Replies
6. Solaris
I'm trying to jumpstart my remote server. My /etc/hosts and /etc/ethers files have the correct data. Keep getting the following message at the ok prompt
after running a boot net - install
Link hasn't comeup yet
Ran a test-net and got the following message.
Link is -- down
When... (7 Replies)
Discussion started by: soupbone38
7 Replies
7. Solaris
Hello everyone,
I tried to install solaris 10 using the command # boot net - install.
I take the image correctly but when you start installing the Operating system installation takes a long (4 hours I have left and not advancing but not send me any errors), it can be seen from the following:
... (7 Replies)
Discussion started by: yflores
7 Replies
8. Solaris
I am performing this installation on a Sun T5220. There is an aftermarket Adaptec StorageTek raid controller card installed. I have created the raid array, and it is referred to as c1t0d0. Here is the profile I have created:
install_type
initial_install
system_type server
cluster SUNWCXall... (4 Replies)
Discussion started by: msarro
4 Replies
9. Solaris
I have a laptop and need to build an Oracle Linux kickstart server and a Solaris Jumpstart server that can build sparc and x86 systems.
Is the best way to create a dual boot from grub for Oracle Linux and Solaris x86?
Can the Oracle Kickstart be used as a Jumpstart to build both Solaris 10... (2 Replies)
Discussion started by: Gian
2 Replies
LEARN ABOUT OPENSOLARIS
ahci
ahci(7D) Devices ahci(7D)
NAME
ahci - Advanced Host Controller Interface SATA controller driver
SYNOPSIS
sata@unit-address
DESCRIPTION
The ahci driver is a SATA framework-compliant HBA driver that supports SATA HBA controllers that are compatible with the Advanced Host Con-
troller Interface 1.0 specification. AHCI is an Intel-developed protocol that describes the register-level interface for host controllers
for serial ATA 1.0a and Serial ATA II. The AHCI 1.0 specification describes the interface between the system software and the host con-
troller hardware.
The ahci driver currently supports the Intel ICH6/7/8/9, VIA vt8251 and JMicron AHCI controllers which are compliant with the Advanced Host
Controller Interface 1.0 specification. Note that while the Intel ICH6/7/8/9, VIA vt8251 and JMicron AHCI controllers support standard
SATA features, the ahci driver currently only supports hard disk, ATAPI SATA DVD, hotplug and NCQ (Native command queuing). Port multiplier
and power management are not yet supported.
CONFIGURATION
The ahci module contains no user configurable parameters.
FILES
/kernel/drv/ahci
32-bit ELF kernel module (x86).
/kernel/drv/amd64/ahci
64-bit ELF kernel module (x86).
ATTRIBUTES
See attributes(5) for descriptions of the following attribute:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Architecture |x86 |
+-----------------------------+-----------------------------+
|Availability |SUNWahci |
+-----------------------------+-----------------------------+
SEE ALSO
cfgadm(1M), cfgadm_sata(1M), prtconf(1M), sata(7D)
Advanced Host Controller Interface 1.0
Writing Device Drivers
NOTES
To bind the ahci driver to your controller, choose the [AHCI] BIOS option.
Note that booting is not supported if toggle exists between the [IDE] and [AHCI] BIOS options
SunOS 5.11 22 Jan 2008 ahci(7D)