08-27-2015
Hi, The service guide instructions are pretty clear. Thanks for your links. I'm not actually using the system to access this page as I'm on a laptop, but when I go to boot the RS 6000 machine from a DVD or try to access SMS, basically on boot up, this is when it asks for the password, although without the password it then goes on to boot the system in to AIX OK and I have the administrator/root password to get in to that. I'll fire it up tomorrow and see what code the panel gives when the firmware password is asked for first.
Thanks
---------- Post updated 27-08-15 at 10:28 AM ---------- Previous update was 26-08-15 at 05:37 PM ----------
Hi Blackrageous, The front panel code I get when it asks for the password is CA00E1A0. Is the pinhole on the front any good to use? I think it resets to factory settings, could I just load AIX after doing that? I haven't got any data I want to save as it's just a machine for learning on.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Have a Sun CDROM connected to a Ultra machine .
Problem is it is not recognizing the drive being connected to it ...
When i put the CD in the drive it accepts the CD and zooms initially then quitens out ..
The devices drivers are also not created for it ...
Any ideas anyone ... I am... (4 Replies)
Discussion started by: Jai
4 Replies
2. Solaris
Good Day,
I've remotely mounted a cdrom (no problems theere). The kicker is I can see the directories on the remote CD bout I can't see the files. What am I doing wrong? I'm logged in as root on both systems. All the permissions seem okay - what am I missing? Thanks (2 Replies)
Discussion started by: greg69
2 Replies
3. Solaris
Morning all,
I am attempting to load a package from a Solaris 8 CDROM.
This fails with the error :
"pkgadd: ERROR: unable to access pkgmap file </cdrom/ .........../SUNWlibC/pkgmap>
No changes were made to the system"
Any help would be appreciated
Andy (6 Replies)
Discussion started by: AndyD
6 Replies
4. Solaris
version of solaris: SunOS 5.8 Generic-117350-39 sun4u sparc SUNW,Netra-240
version of SSH: OpenSSH_4.4p1, OpenSSL 0.9.8d 28 Sep 2006
Task:
I need to have another Machine ssh into my machine, by either RSA authentication or username/pass authentication.
History:
In the begining my... (4 Replies)
Discussion started by: EWTGPAC
4 Replies
5. Solaris
Hi:
I have a Sun Blade 1500 and when I do the Jumpstart with
command "boot net - install" asking for the password of the firmware
and I was not that password. There any way to reset this password.
Thank you very much (7 Replies)
Discussion started by: ea1fch
7 Replies
6. Solaris
So in the group of boxes I've inherited, I have one that has a firmware password. I do not know the root password of the machine nor the firmware password. I've tried several things already, such as: removing BIOS battery, double tap the power switch, and several variants of the STOP-A on a PC... (2 Replies)
Discussion started by: adelsin
2 Replies
7. Solaris
Greetings Forumers!
I've been fighting a locale problem on a v490 running Solaris 10 u4 (8/07). When I login to the system, I get several "locale" error messages:
user1's password:
Last login: Wed May 26 2010 09:14:13 -0400 from system1
You have mail.
couldn't set locale correctly
couldn't... (0 Replies)
Discussion started by: bluescreen
0 Replies
8. Solaris
Hi:
I bougth an used Sun Fire v440, and It have a firmware password. When I turn on the server, it ask for firmware password. (I don 't know what is the correct password). I can access to SC, but when I want to access to OBP, Firmware Password appears again. I remove the battery for two hours,... (1 Reply)
Discussion started by: mguazzardo
1 Replies
9. Solaris
Hey,
I have been battling with jumpstart for the past few days. Interface nxge0 is set on a vlan:
nxge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet 0.0.0.0 netmask ff000000
ether 0:21:28:3c:a0:6
nxge998000:... (0 Replies)
Discussion started by: stantonnet
0 Replies
10. AIX
Hi all
With the recent virus attacks we have been tasked with upgrading Samba to a "secure" version. Currently running 3.0.29a and looking to put the latest version down 4.6.5.
Being a lazy bod I have only ever installed this, a long time ago, when you could get it in BFF filesets. Have... (6 Replies)
Discussion started by: splattty
6 Replies
LEARN ABOUT OPENDARWIN
nvram
nvram(8) System Manager's Manual nvram(8)
NAME
nvram - manipulate Open Firmware NVRAM variables
SYNOPSIS
nvram [ -p ] [ -f filename ] [ name ] [= value ] ...
DESCRIPTION
The nvram command allows manipulation of Open Firmware NVRAM variables. It can be used to get or set a variable. It can also be used to
print all of the variables or set a list of variables from a file. Changes to NVRAM variables are only saved by clean restart or shutdown.
In principle, name can be any string. In practice, not all strings will be accepted. New World machines can create new variables as
desired. Some variables require administrator privilege to get or set.
The given value must match the data type required for name. Binary data can be set using the %xx notation, where xx is the hex value of
the byte. The type for new variables is always binary data.
OPTIONS
-p Print all of the Open Firmware variables.
-f filename
Set Open Firmware variables from a text file. The file must be a list name=value statements. If the last character of a line is ,
the value will be continued to the next line.
EXAMPLES
example% nvram boot-args="-s rd=*hd:10"
Set the boot-args variable to "-s rd=*hd:10". This would specify single user mode with the root device in hard drive partition 10.
example% nvram my-variable="String One%00String Two%00%00"
Create a new variable, my-variable, containing a list of two C-strings that is terminated by a NUL.
December 12, 2000 nvram(8)