|
|
Sponsored Content
Operating Systems
Solaris
Zfs rpool size
Post 302953033 by freshmeat on Tuesday 25th of August 2015 04:05:43 AM
08-25-2015
rpool/dump volsize 20G local
rpool/swap volsize 16G local
I have cleared some snapshots, now the snapshot with compression size is around 13GB. I am still thinking to reduce it below 10GB because I have disk space constraints.
rpool/swap volsize 16G local
I have cleared some snapshots, now the snapshot with compression size is around 13GB. I am still thinking to reduce it below 10GB because I have disk space constraints.
|
|
10 More Discussions You Might Find Interesting
1. Solaris
I was able to create a zpool and then created a zfs filesystem (BTW, thanks to all those who helped me get by the hard drive formatting issues I had posted here earlier).
I read that ZFS does variable block size, that is, a user can specify a blocksize, and if a file is smaller than the user... (1 Reply)
Discussion started by: sqa777
1 Replies
2. Solaris
My system is showing following .. how can i remove this rpool .. ?
zpool status -v rpool
pool: rpool
state: UNAVAIL
status: One or more devices could not be opened. There are insufficient
replicas for the pool to continue functioning.
action: Attach the missing device and... (0 Replies)
Discussion started by: fugitive
0 Replies
3. Solaris
Hi,
kstat -p -m zfs -n arcstats -s size returns
zfs:0:arcstats:size 8177310584
this values is approx (7.61 GB)
but my Physical Memory size is only 6144 Megabytes.
Can this happen ?
if yes, then how can I find free memory on the system.
BTW, I ran the kstat commands from a Non... (2 Replies)
Discussion started by: sapre_amit
2 Replies
4. Solaris
I'd like to finish setting up this system and then move the secondary or primary disk to another system that is the exact same hardware.
I've done things like this in the past with ufs and disk suite mirroring just fine. But I have yet to do it with a zfs root pool mirror.
Are there any... (1 Reply)
Discussion started by: Metasin
1 Replies
5. Solaris
Hi,
I have Solaris-10 (release-7) box without any non global zone. I have a very critical change after couple of days from application side. For safer side, we want to keep few level of backups just in case of faliure. This server is having three pool
root@prod_ddoa01:/# zpool list
NAME SIZE... (2 Replies)
Discussion started by: solaris_1977
2 Replies
6. Solaris
Hi,
I have rpool about 500G. So i want to use 210G from rpool and assign mount point as /database.
I seek in google and couldn't found it. Does anyone know how to achieve it?
Thanks. (2 Replies)
Discussion started by: mzainal
2 Replies
7. Solaris
Hi,
I am unable to understand that, in one of my servers while
df -kh
Filesystem Size Used Available Capacity Mounted on
rpool/ROOT/solaris-2 98G 11G 29G 29% /
Even the Root FS filled on 40gb and system becomes unstable.
it is showing... (4 Replies)
Discussion started by: anuragr
4 Replies
8. Solaris
Hi,
I have this fresh installation of Solaris 11.3 sparc.
I have two zfs pools both using two disks in mirroring mode, both are online.
I want to move /system/zones, currently rpool/VARSHARE/zones, from rpool to the other zfs pool so my zones don't consume space on the disks allocated to... (1 Reply)
Discussion started by: X96
1 Replies
9. Solaris
I have a 240GB disk as rpool. I have installed Solaris 11.3 to a partition which is 110GB. Now I have another 130GB which is unallocated. I want to use that additional space as a temporary folder to be shared between Solaris and Linux. The additional space had no /dev/dsk/c2t4... entry so I used... (8 Replies)
Discussion started by: kebabbert
8 Replies
10. Solaris
Hi
Please let me know how to increase the size of rpool in solaris 11 in ldom. I know how to map the new LUN to LDOM after that please let me know the procedure to increase the rpool and how to identify new disk in OBP level of ldom as I need to set the new/lun to be my new boot device. (5 Replies)
Discussion started by: hb00
5 Replies
LEARN ABOUT DEBIAN
g3dviewer
G3DVIEWER(1) General Commands Manual G3DVIEWER(1) NAME
g3dviewer - a program to display and inspect 3D models SYNOPIS
g3dviewer [options] [<filename>] DESCRIPTION
After loading a valid model it should appear on the screen. Use the left mouse button to rotate the model. To move the view hold down the SHIFT key and use left mouse button. To zoom the model use the scroll wheel or hold the middle mouse button and move the mouse up or down. The right mouse button opens a context menu where you can open the model information dialog, set some options or change the background color. OPTIONS
--help Show summary of options "UNDOCUMENTED" OPTIONS There are also some options which are just for development. --parse-only Just parse the model and exit. SUPPORTED FILE TYPES
.3mf, 3dmf 3D Metafiles. .3ds, .prj 3D Studio objects. .b3d unknown, but 3D Metafile format. .cob Caligary TrueSpace objects. .dxf AutoCAD models. .iob Impulse Turbo Silver / Imagine objects. .lw, .lwo, .lwb LightWave objects. .md2 Quake 2 models. .nff Neutral File Format objects. .obj Wavefront objects. .q3o, .q3s Quick3D objects and scenes. .wrl VRML worlds. BUGS
Most import plugins are incomplete. The goal is not to crash on broken input but it is not always reached. AUTHOR
g3dviewer was written by Markus Dahms <mad@automagically.de> july 22nd 2005 G3DVIEWER(1)