|
|
Sponsored Content
Operating Systems
Solaris
Zfs rpool size
Post 302953025 by freshmeat on Tuesday 25th of August 2015 02:38:14 AM
08-25-2015
Zfs rpool size
Hi everyone,
I am doing housekeeping of my Solaris 11 for zfs snapshot to reduce the snapshot size. I have already cleared the / file system, however the rpool size still not reduced.
Filesystem Size Used Available Capacity Mounted on
rpool/ROOT/solaris-2 98G 6.9G 35G 17% /
NAME USED AVAIL REFER MOUNTPOINT
rpool 62.6G 35.4G 73.5K /rpool
What are the files are used up the disk space? Please assist. Thanks.
I am doing housekeeping of my Solaris 11 for zfs snapshot to reduce the snapshot size. I have already cleared the / file system, however the rpool size still not reduced.
Filesystem Size Used Available Capacity Mounted on
rpool/ROOT/solaris-2 98G 6.9G 35G 17% /
NAME USED AVAIL REFER MOUNTPOINT
rpool 62.6G 35.4G 73.5K /rpool
What are the files are used up the disk space? Please assist. Thanks.
|
|
10 More Discussions You Might Find Interesting
1. Solaris
I was able to create a zpool and then created a zfs filesystem (BTW, thanks to all those who helped me get by the hard drive formatting issues I had posted here earlier).
I read that ZFS does variable block size, that is, a user can specify a blocksize, and if a file is smaller than the user... (1 Reply)
Discussion started by: sqa777
1 Replies
2. Solaris
My system is showing following .. how can i remove this rpool .. ?
zpool status -v rpool
pool: rpool
state: UNAVAIL
status: One or more devices could not be opened. There are insufficient
replicas for the pool to continue functioning.
action: Attach the missing device and... (0 Replies)
Discussion started by: fugitive
0 Replies
3. Solaris
Hi,
kstat -p -m zfs -n arcstats -s size returns
zfs:0:arcstats:size 8177310584
this values is approx (7.61 GB)
but my Physical Memory size is only 6144 Megabytes.
Can this happen ?
if yes, then how can I find free memory on the system.
BTW, I ran the kstat commands from a Non... (2 Replies)
Discussion started by: sapre_amit
2 Replies
4. Solaris
I'd like to finish setting up this system and then move the secondary or primary disk to another system that is the exact same hardware.
I've done things like this in the past with ufs and disk suite mirroring just fine. But I have yet to do it with a zfs root pool mirror.
Are there any... (1 Reply)
Discussion started by: Metasin
1 Replies
5. Solaris
Hi,
I have Solaris-10 (release-7) box without any non global zone. I have a very critical change after couple of days from application side. For safer side, we want to keep few level of backups just in case of faliure. This server is having three pool
root@prod_ddoa01:/# zpool list
NAME SIZE... (2 Replies)
Discussion started by: solaris_1977
2 Replies
6. Solaris
Hi,
I have rpool about 500G. So i want to use 210G from rpool and assign mount point as /database.
I seek in google and couldn't found it. Does anyone know how to achieve it?
Thanks. (2 Replies)
Discussion started by: mzainal
2 Replies
7. Solaris
Hi,
I am unable to understand that, in one of my servers while
df -kh
Filesystem Size Used Available Capacity Mounted on
rpool/ROOT/solaris-2 98G 11G 29G 29% /
Even the Root FS filled on 40gb and system becomes unstable.
it is showing... (4 Replies)
Discussion started by: anuragr
4 Replies
8. Solaris
Hi,
I have this fresh installation of Solaris 11.3 sparc.
I have two zfs pools both using two disks in mirroring mode, both are online.
I want to move /system/zones, currently rpool/VARSHARE/zones, from rpool to the other zfs pool so my zones don't consume space on the disks allocated to... (1 Reply)
Discussion started by: X96
1 Replies
9. Solaris
I have a 240GB disk as rpool. I have installed Solaris 11.3 to a partition which is 110GB. Now I have another 130GB which is unallocated. I want to use that additional space as a temporary folder to be shared between Solaris and Linux. The additional space had no /dev/dsk/c2t4... entry so I used... (8 Replies)
Discussion started by: kebabbert
8 Replies
10. Solaris
Hi
Please let me know how to increase the size of rpool in solaris 11 in ldom. I know how to map the new LUN to LDOM after that please let me know the procedure to increase the rpool and how to identify new disk in OBP level of ldom as I need to set the new/lun to be my new boot device. (5 Replies)
Discussion started by: hb00
5 Replies
LEARN ABOUT NETBSD
fssconfig
FSSCONFIG(8) BSD System Manager's Manual FSSCONFIG(8) NAME
fssconfig -- configure file system snapshot devices SYNOPSIS
fssconfig [-cxv] device path backup [cluster [size]] fssconfig -u [-v] device fssconfig -l [-v] [device] DESCRIPTION
The fssconfig command configures file system snapshot pseudo disk devices. It will associate the file system snapshot disk device with a snapshot of path allowing the latter to be accessed as though it were a disk. If backup resides on the snapshotted file system a persistent snapshot will be created. This snapshot is active until backup is unlinked. This snapshot mode is only supported for ffs files systems. Otherwise data written through the path will be saved in backup. If backup is a regular file, it will be created with length size. Default size is the size of path. Data is saved to backup in units of cluster bytes. Options indicate an action to be performed: -c Configures the device. If successful, references to device will access the contents of path at the time the snapshot was taken. If backup is a directory, a temporary file will be created in this directory. This file will be unlinked on exit. -l List the snapshot devices and indicate which ones are in use. If a specific device is given, then only that will be described. -u Unconfigures the device. -v Be more verbose listing the snapshot devices. -x Unlink backup after the device is configured. If no action option is given, -c is assumed. FILES
/dev/rfss? /dev/fss? EXAMPLES
fssconfig fss0 /usr /tmp/back Configures the snapshot device fss0 for a snapshot of the /usr file system. Data written through /usr will be backed up in /tmp/back. fssconfig fss1 / /dev/rsd0e 8192 Configures the snapshot device fss1 for a snapshot of the / file system. Data written through / will be backed up in /dev/rsd0e. The backup will take place in units of 8192 bytes. fssconfig -u fss0 Unconfigures the fss0 device. SEE ALSO
opendisk(3), fss(4), mount(8), umount(8) HISTORY
The fssconfig command appeared in NetBSD 2.0. BSD
June 11, 2012 BSD