Dear all,
After succesful installation of UNIX SCO WARE 7.0, while booting the system it is displaying as follows:
The kernel will be rebuilt to incorporate recent configaration changes
Press Enter when ready OR
Press Escape to Stop.
While pressing Enter, message is coming again and again... (2 Replies)
Now it could be as simple as at work I use tsch, and at home it is bash.
Warning, first post and I am a complete newbie to unix.
At work, I use a simple script for updating a window when I am watching to see how a render is doing...
while 1
echo ---------------------------
echo
ls -lrth... (1 Reply)
I can't find a source rpm for a particular tool that I'm trying to modify. I can only get a hold of the noarch and tar.bz2. Can I modify either one of these and re-package them as a noarch.rpm? (2 Replies)
Hi guys,
I need to find tomorrows date in date fomat and should be in variable.
as I need to grep this date in a flat file
ie. if today's date is '09 JAN 2009'
output should be '10 JAN 2009'
unix/perl script will be fine. (21 Replies)
I need opinion from other !
I finished high school for computer technician few months ago and now I can not find a job because I do not have any experience with servers , I know basic staff about Linux and Unix and Windows better (used three 4 years) (this is way I registered here at... (3 Replies)
Hi Guru's,
I'm trying to rebuild a very old HMC 7315-C02 the hard disk has gone so needs replacing. I've managed to find an old IDE hard disk lying around but its obvious that it's had windows running on it as the HMC install disks won't recognise the format. I'm trying to install HMC V6 R1.2... (3 Replies)
I guess Mac has default bash. Then I copy my code to another comp and run it...And it gives me an error like "bad substitution"....
How I can change my code??? Never had before this kind of situation. Help please.
if
then
n=$(sort /Users/Natalie/lastserial | tail -1)
... (6 Replies)
so i have many scripts that have to run when the bash source is installed as normal.
however, some users have found a way to build bash from source and while doing so, they altered some default settings.
my question is, what can i put in my script to check that the "flags.c" binary and... (6 Replies)
Discussion started by: SkySmart
6 Replies
LEARN ABOUT CENTOS
iscsiuio
iscsiuio(8) System Manager's Manual iscsiuio(8)NAME
iscsiuio - iSCSI UserSpace I/O driver
SYNOPSIS
iscsiuio [-d-f-v]
DESCRIPTION
iscsiuio is the UserSpace I/O driver for the Broadcom NetXtreme II BCM5706/5708/5709 series PCI/PCI-X Gigabit Ethernet Network Interface
Card (NIC) and for the Broadcom NetXtreme II BCM57710/57711/57712/57800/57810/57840 series PCI-E 10 Gigabit Ethernet Network Interface
Card. The driver has been tested on 2.6.28 kernels and above.
Refer to the README.TXT from the driver package on how to compile and install the driver.
Refer to various Linux documentations on how to configure network protocol and address.
DRIVER DEPENDENCIES PARAMETERS
There are very few parameters when running this application.
-d<debuglevel>
This is to enable debug mode where debug messages will be sent to stdout The following debug modes are supported
DEBUG 4 - Print all messages
INFO 3 - Print messages needed to follow the uIP code (default)
WARN 2 - Print warning messages
ERROR 1 - Only print critical errors
-f This is to enable forground mode so that this application doesn't get sent into the background.
-v This is to print the version.
-p<pidfile>
Use pidfile (default /var/run/iscsiuio.pid )
-h Display this help and exit.
AUTHOR
Benjamin Li - benli@broadcom.com
Eddie Wai - eddie.wai@broadcom.com
Broadcom Corporation 12/10/2013 iscsiuio(8)