08-05-2015
Automatic Server bootup after power outage?
Hi everyone,
We had a power outage few days ago, and I got the servers up and running but I was informed to look into, if there is a way to bring up the servers automatically/defaultly.
I was told the windows admin has their server set up where the servers are up automatically if there is a power outage.. manager told me
"look in to the Bios". I didn't know what that meant, but only stuff I found was on windows servers....
I found this link but it talks about dell server.
East Bay Solutions :: Automatically turning computer back on after power outage
Any information will be greatly appreciated.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Evry time I start up my mavhine ,have to type in unix at
Boot
:
Is there a way unix should bootup automatically?
Asif (2 Replies)
Discussion started by: asif iqbal
2 Replies
2. Solaris
hi guys,
i'm new so don't bite too hard.
having a problem booting up a V210 running sol9 on after a power outage...
an init5 was done but not a init0 before the power cut... so now when booting up it gives the ff:
SC Alert: Host System has Reset
Probing system devices
Probing memory... (2 Replies)
Discussion started by: lungsta
2 Replies
3. AIX
Issue: AIX server freezes on bootup.
Server AIX ver 4.3.3.0
When the AIX server reboots it negotiates NIS. During startup of NFS, customer gets one or more of the following error messages:
0513-056 Timeout waiting for command response. If you specified a foreign host, see the /etc/inittab file... (1 Reply)
Discussion started by: srzaman1
1 Replies
4. Solaris
Hi all,
I have a server SUN FUJITSU in solaris 10 ; result of uname -a is :
SunOS MOBD1 5.10 Generic_118833-03 sun4us sparc FJSV,GPUZC-M
I have configured the eeprom to auto-boot as usual and this automatic reboot does not work in case of power failure. I must type "boot" on the prompt "ok"... (5 Replies)
Discussion started by: aribault
5 Replies
5. Linux
Hello all,
I have a script callled 'ABCstartup' setup under /etc/rc.d/init.d
Softlink 'S91ABCstartup' pointing to above script has been created under /etc/rc.d/rc3.d
The script is not being executed when the server restarts.
The script runs successfully via manual execution:... (5 Replies)
Discussion started by: hemangjani
5 Replies
6. AIX
i am new to aix environment and all my servers are @ remote location
just curious to know , what issues/tasks we will be facing when there is a power outage in a data centre, i heard outage's will be a challenging task for administrators.. any example of that sort will be a great help (2 Replies)
Discussion started by: rigin
2 Replies
7. Linux
Hi guys,
I was wondering if you could share some of your knowledge, in the event of a power outage.
Let presume you are on duty and you get a call at midnight because half of your cabinets have no power, air conditioning is down and you deal with a ton of 500 error messages on your boxes.
... (9 Replies)
Discussion started by: TECK
9 Replies
8. Solaris
Hi,
Would like to know the uptime or specific time limit to reboot the sun microsystem to avoid unplanned outage.
Regards,Tarun (9 Replies)
Discussion started by: taruntan
9 Replies
9. Red Hat
We have Linux Server crash on last Friday of 25th It's is running on IBM x3650 hardware. We Have Red Hat Enterprise Linux Server release 5.9 (Tikanga) running on top of it.
We were told to do Root Cause Analysis. So, Apart from looking /var/log/messages, Where can we check to get details on... (3 Replies)
Discussion started by: Sunil Koya
3 Replies
10. AIX
Hello Forum,
I am very newbie with AIX.
We have 2 AIX 9111-285 servers. The OS version is 5.3.
After the power outage, they did not come up.
I try to unplug the power cable and re-connect after 1 minutes but do not help.
Both display the same reference code 110000AC on the front panel... (6 Replies)
Discussion started by: lilyn
6 Replies
LEARN ABOUT DEBIAN
kumoctl
KUMOCTL(1) General Commands Manual KUMOCTL(1)
NAME
kumoctl - show kumofs status
SYNOPSIS
kumoctl address[:port=19750] command [options]
DESCRIPTION
Show status of kumo-manager and send control commands to kumo-manager.
COMMANDS
status show status of the cluster
attach attach all new servers and start replace
attach-noreplace
attach all new servers
detach detach all fault servers and start replace
detach-noreplace
detach all fault servers
replace
start replace without attach/detach
full-replace
start full-replace (repair consistency)
backup [suffix=20090304]
create backup with specified suffix
enable-auto-replace
enable auto replace
disable-auto-replace
disable auto replace
STATUS
hash space timestamp
The time that the list of attached kumo-servers is updated. It is updated when new kumo-server is added or existing kumo-server is
down.
attached node
The list of attached kumo-servers. (active) is normal node and (fault) is fault node or recoverd but not re-attached node.
not attached node
The list of recognized but not-attached nodes.
AUTO REPLACING
By default, you have to attach new kumo-servers manually using kumoctl command. If the auto replacing is enabled, new kumo-servers are
attached automatically. This is experimental feature.
EXAMPLE
$ kumoctl mgr1 status
$ kumoctl mgr1 attach
SEE ALSO
kumo-manager(1).
kumoctl July 2009 KUMOCTL(1)