|
|
Sponsored Content
Operating Systems
HP-UX
Expert Recovery Shell - Fatal Error: Unrecognized disk layout
Post 302949961 by Peasant on Saturday 18th of July 2015 03:13:12 AM
07-18-2015
Moderator
Do you have other disks inside on which you can install hpux v3 ?
If you can install on another disk, you should be able to mount the disk in question after installing the required depot drivers.
At least you will be able to access the data on them and manipulate them in certain ways.
What kind of mirror is it (controller or LVM)
It is a good practice to have ignite backups.
If you can install on another disk, you should be able to mount the disk in question after installing the required depot drivers.
At least you will be able to access the data on them and manipulate them in certain ways.
What kind of mirror is it (controller or LVM)
It is a good practice to have ignite backups.
|
|
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
I have a doubt with an error message, and i want to be sure if this is a normal situation or not.
Situation: I was formating and installing a SCSI 36Gb HD with UNIX SCO 5.05, the problem happens when is making the division and filesystem on disk 1, and the message error is "Exit value 139... (1 Reply)
Discussion started by: jav_v
1 Replies
2. UNIX for Dummies Questions & Answers
Apologize if I hurt anyone's head with my questions, I'm entirely new to Unix and my office here doesn't offer any training just learn as you go. Anyways they asked me to get a disk layout of one of our servers and gave me this as an example the lables are assumptions
Disk ... (2 Replies)
Discussion started by: newdigitalblue
2 Replies
3. Solaris
Hi
I am unable to understand the disk layout of one of my disk attached to v240. This is newly installed system from jumpstart.
I am unable to see the free space on backup slice 2 and there are 0 to 8 slices listed when I run format and print the disk info, also there is no reference of... (9 Replies)
Discussion started by: kumarmani
9 Replies
4. UNIX for Advanced & Expert Users
I am trying to build a veritas volume similar to an existing volume on another server. The output on source server is:
usbtor12# vxprint -hrtg appdg
v anvil_sqlVOL - ENABLED ACTIVE 629145600 SELECT - fsgen
pl anvil_sqlVOL-01 anvil_sqlVOL ENABLED ACTIVE 629145600... (3 Replies)
Discussion started by: momin313
3 Replies
5. Hardware
I have a external HD that I can't seem to open. When I try to open it with gparted it says unrecognized disk. When I run gparted from the terminal this is what it says.
~ $ sudo gparted
======================
libparted : 2.2
======================
/dev/sdb: unrecognised disk label
When I... (18 Replies)
Discussion started by: cokedude
18 Replies
6. AIX
my users has requested more space to a particular volume group, so i do a lsvg
honda:/tmp/ab/ecc # lsvg
rootvg
OP24BCKVG
OP24ORAvg
OP24SYSVG
OP24DATVG
the user wants to know what disks are available to be added to any of the vgs listed above, (not including rootvg)
so i do a lspv... (2 Replies)
Discussion started by: asyed123
2 Replies
7. Hardware
Hi everyone,
I have an external hard drive and I accidentally deleted the partition table.
Can I restore my files?
If I try to run the f-disk command this is what it says
Disk /dev/sda: 320.1 GB, 320072933376 bytes
255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors
Units =... (1 Reply)
Discussion started by: Sampa
1 Replies
8. SCO
Dear Community!
i try to instaled the sco 6 in hp proliant ML350g8
but unsucces,
the trouble when i do instaled it undetected hardisk
please help me
:(:o (7 Replies)
Discussion started by: mnr
7 Replies
9. Solaris
Hi,
I installed some packages required by an app built with python.
But when I try python setup.py install, I get the following error:
/opt/csw/lib/gcc/sparc-sun-solaris2.10/5.2.0/../../../../sparc-sun-solaris2.10/bin/as: unrecognized option `-m32'
Could anyone tell me what's wrong... (4 Replies)
Discussion started by: Kimkun
4 Replies
10. What is on Your Mind?
Today, I noticed some errors in our SSL cert renewal log files, mostly related to domains where the IP address had changed. Concerned about this, rebuilt out SSL cert, which normally goes well without a hiccup.
However, for today, for some reason which I cannot explain, there was a PHP error... (0 Replies)
Discussion started by: Neo
0 Replies
LEARN ABOUT LINUX
pccbb
PCCBB(4) BSD Kernel Interfaces Manual PCCBB(4) NAME
pccbb -- cardbus bridge driver SYNOPSIS
device cbb device pccard device cardbus device exca DESCRIPTION
The pccbb driver implements the Yenta specification for CardBus bridges. The following PCI cardbus and pcmcia bridges are supported: Cirrus Logic PD6832 Cirrus Logic PD6833 Cirrus Logic PD6834 O2micro OZ6812 O2micro OZ6832 O2micro OZ6833 O2micro OZ6836 O2micro OZ6860 O2micro OZ6872 O2micro OZ6912 O2micro OZ6922 O2micro OZ6933 O2micro OZ6972 O2Micro OZ711E1 O2Micro OZ711M1 Ricoh RL4C475 Ricoh RL4C476 Ricoh RL4C477 Ricoh RL4C478 TI PCI-1031 TI PCI-1130 TI PCI-1131 TI PCI-1210 TI PCI-1211 TI PCI-1220 TI PCI-1221 TI PCI-1225 TI PCI-1250 TI PCI-1251 TI PCI-1251B TI PCI-1260 TI PCI-1260B TI PCI-1410 TI PCI-1420 TI PCI-1450 TI PCI-1451 TI PCI-1510 TI PCI-1515 TI PCI-1520 TI PCI-1530 TI PCI-1620 TI PCI-4410 TI PCI-4450 TI PCI-4451 TI PCI-4510 TI PCI-4520 TI PCI-[67]x[12]1 TI PCI-[67]x20 ENE CB710 ENE CB720 ENE CB1211 ENE CB1255 ENE CB1410 ENE CB1420 Toshiba ToPIC95 Toshiba ToPIC95B Toshiba ToPIC97 Toshiba ToPIC100 TUNABLES
The driver supports the following tunable parameters, which may be added to /boot/loader.conf or set via the sysctl(8) command: hw.cbb.debug Non-zero values cause more verbose information to be printed to aid in debugging problems with the bridge chipset. SEE ALSO
cardbus(4), pccard(4), exca(4) BSD
July 21, 2004 BSD