07-08-2015
You didn't answer my post#36. Did the analyse error out in a few seconds or did it run for a long time? I'm trying to ascertain whether sectors on your drive can be read or not.
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hi,
when installing a piece of third part software I get the error "Bad magic number" at one point when it tries to use libraries from the bea tuxedo server. Am I correct that this means that the software is expecting 32bit while I'm on 64bit? Is there a way around it or can it only be solved... (5 Replies)
Discussion started by: rein
5 Replies
2. Solaris
I tried rebooting my Sun server just a few minutes ago and I got the following at boot:
--
Sun Fire 280R (UltraSPARC-III+) , No Keyboard
Copyright 1998-2002 Sun Microsystems, Inc. All rights reserved.
OpenBoot 4.5, 1024 MB memory installed, Serial #xxxxxxxxx
Ethernet address... (6 Replies)
Discussion started by: deckard
6 Replies
3. Filesystems, Disks and Memory
Dear All,
i have a SCSI hard disk drive i'm installing on it solaris 5 and the workstation is sun sparc, i made an image of this H.D using Norton Ghost 6, so i took off the SCSI H.D from the sun workstation and put it on a Compaq server then i booted the server from the Norton Ghost floppy disk... (0 Replies)
Discussion started by: wesweshahaha
0 Replies
4. UNIX for Advanced & Expert Users
Hello All,
(RHEL4)
Few weeks ago I had posted a message in this forum about the problem I had when I replaced my two scsi disks and tried rebuild raid1 array.
I somehow managed to up the system with working raid1 array.
But the main problem persisted..
i.e when I reboot the system, mounting... (0 Replies)
Discussion started by: ravinandan
0 Replies
5. Solaris
Hello All,
I m very new to this forum.
i m having SUN NETRA X1 server with 40 GB HDD (Seagate) & 128 MB RAM.
i m trying this server for SUN 10 Practise.
As i m installing SUN 9 /10 with CD ,its giving me error after OK propmt
***************************
#boot cdrom
or
#boot cdrom... (16 Replies)
Discussion started by: amrut_k
16 Replies
6. Solaris
Hello,
I'm brand new to Sun/Solaris.
I have a Sun Blade 150, with SunOS 5.8.
I wanted to make a backup to prevent future data loss, so I put the disk in a normal PC with Windows XP to try to make a backup with Norton Ghost, the disk was detected, but not the file volume, so I place the disk... (6 Replies)
Discussion started by: Resadija
6 Replies
7. Solaris
I'll keep it fairly straight forward. I work with a Solaris server and magically today it decided to take a dump on me. At first it give a long list of files that couldn't be acessed before terminating the boot process and returning to the 'ok' prompt. Booting in single-user mode allowed me to run... (4 Replies)
Discussion started by: Aon
4 Replies
8. Solaris
I have created 1 LUN.
1)LUN 00BB 200GB /dev/rdsk/c1t3d44
/dev/rdsk/c2t28d44
/dev/rdsk/c3t19d44
/dev/rdsk/c4t12d44
2) Already added the new entry into sd.conf and rebooted.
3) Already done these:
powercf –q
power config
4) power display dev=all
I can see the new Symmetrix device.... (1 Reply)
Discussion started by: sirius20d
1 Replies
9. Solaris
Is there a way to recover label?
I could install (sparc) Solaris again, but it would take a lot of time. (5 Replies)
Discussion started by: orange47
5 Replies
10. Solaris
So we have a new to us v240 server with no OS installed. It has an outdated version of OB and ALOM so before we install the OS we want to update both. We have a DVD with the latest OB patch burned on it.
We do the boot cdrom command but receive the Bad Magic Number Error. Does an OS need to... (2 Replies)
Discussion started by: dunkpancakes
2 Replies
LEARN ABOUT NETBSD
mbrlabel
MBRLABEL(8) BSD System Manager's Manual MBRLABEL(8)
NAME
mbrlabel -- update disk label from MBR label(s)
SYNOPSIS
mbrlabel [-fqrw] [-s sector] device
DESCRIPTION
mbrlabel is used to update a NetBSD disk label from the Master Boot Record (MBR) label(s) found on disks that were previously used on
DOS/Windows systems (or other MBR using systems).
mbrlabel scans the MBR contained in the very first block of the disk (or the block specified through the -s flag), then walks through every
extended partition found and generates additional partition entries for the disk from the MBRs found in those extended partitions.
Each MBR partition which does not have an equivalent partition in the disk label (equivalent in having the same size and offset) is added to
the first free partition slot in the disk label. A free partition slot is defined as one with an fstype of 'unused' and a size of zero
('0'). If there are not enough free slots in the disk label, a warning will be issued.
The raw partition (typically partition c, but d on i386 and some other platforms) is left alone during this process.
By default, the proposed changed disk label will be displayed and no disk label update will occur.
Available options:
-f Force an update, even if there has been no change.
-q Performs operations in a quiet fashion.
-r In conjunction with -w, also update the on-disk label.
-s sector Specifies the logical sector number that has to be read from the disk in order to find the MBR. Useful if the disk has remapping
drivers on it and the MBR is located in a non-standard place. Defaults to 0.
-w Update the in-core label if it has been changed. See also -r.
SEE ALSO
disklabel(8), dkctl(8), fdisk(8), mbr(8)
HISTORY
The mbrlabel command appeared in NetBSD 1.4.
BSD
April 5, 2010 BSD