06-23-2015
9 More Discussions You Might Find Interesting
1. Post Here to Contact Site Administrators and Moderators
Just a remark now the board has grown to considerable proportion. I see too little of an active hand(s) maintaning the boards, clipping away dead posts, moving posts that were created in the wrong forums etc. It's a bit tiring to see alot of threads ending in: this has been covered before, do a... (7 Replies)
Discussion started by: patvdv
7 Replies
2. What is on Your Mind?
Hi Admin and Staff...
Thanks for hosting AudioScope.sh on this site. I have had the biggest surprise of my life today.
This months issue of the UK Linux magazine "Linux Format" have done a small piece on the project.
Issue April 2014, LXF 182, page 65...
This I never expected and I... (1 Reply)
Discussion started by: wisecracker
1 Replies
3. OS X (Apple)
Hi all...
Has _below_ ever been done in UNIX shell scripting before?
(I have done this easily in Python but this is using purely the shell.)
The DEMO version IS built and has been tested.
Pre-amble...
I now need at least one control pulse for the AudioScope.sh when in PURELY audio I/O mode,... (2 Replies)
Discussion started by: wisecracker
2 Replies
4. Shell Programming and Scripting
Development machine:- Standard MBP 13 inch, OSX 10.7.5...
GNU bash, version 3.2.48(1)-release (x86_64-apple-darwin11)
Copyright (C) 2007 Free Software Foundation, Inc.
Scenario:- Audio capture for AudioScope.sh for CygWin without ANY third party installs.
I am trying my hardest to get a... (6 Replies)
Discussion started by: wisecracker
6 Replies
5. How to Post in the The UNIX and Linux Forums
Can please somebody tell me what could be the reason for the following error (Unix Motorola Server):
/usr/etc/ce3/s374: Board at address 0xff10000 not present - Entry skipped.
/dev/lpc2: I/O error
I already replaced the board 374 on the server, but I have the same problem.
Thank you! (1 Reply)
Discussion started by: dma
1 Replies
6. What is on Your Mind?
Boy oh boy, with only a MONO mic input to use AudioScope gets much more difficult when the ALTDC board is included.
It needs, so far, two hits at the MIC input with a single hit at the HEADPHONE audio output.
The first at the highest practical resolution for the AC component and the second... (0 Replies)
Discussion started by: wisecracker
0 Replies
7. OS X (Apple)
Hi all...
Apologies for any typos...
For those intersted in the AudioScope the next construction is finished.
I have not been totally idle but working out the hard stuff to be able to be very simple to build.
It is a single transistor simple timer that lasts for about 1.2 to 1.8 seconds.... (2 Replies)
Discussion started by: wisecracker
2 Replies
8. UNIX for Advanced & Expert Users
Using AudioScope.sh on Ubuntu 17.04 from a live DVD disc I came across an error.
Consider the code below it is a MUCH shortened version of the KEYBOARD input in AudioScope.
#!/bin/bash
bash --version
uname -a
status=0
KEYBOARD()
{
read -r -p "Enter QUIT or EXIT to quit:- " kbinput
if ||... (11 Replies)
Discussion started by: wisecracker
11 Replies
9. OS X (Apple)
AudioScope Project.
(Apologies for any typos.)
For the few following......
AudioScope.sh...
Now at Version 0.60.00.
Well this baby has come a long way since its inception in January 2013. It is now at Version 0.60.00. It is MUCH more Apple centric now with a new OSX Sierra minimum _silent_... (7 Replies)
Discussion started by: wisecracker
7 Replies
LEARN ABOUT DEBIAN
cobertura-check
COBERTURA-CHECK(1) General Commands Manual COBERTURA-CHECK(1)
NAME
cobertura-check -- show which classes do not have adequate test coverage
SYNOPSIS
cobertura-check [--branch 0..100] [--datafile file] [--line 0..100] [--regex regex:branchrate:linerate] [--packagebranch 0..100]
[--packageline 0..100] [--totalbranch 0..100] [--totalline 0..100]
DESCRIPTION
cobertura-check can be run after your JUnit tests to show which classes do not have adequate test coverage.
OPTIONS
If no parameters are specified then all values will be set to 50%.
--branch 0..100
Specify the minimum acceptable branch coverage rate needed by each class. This should be an integer value between 0 and 100.
Default value is 0.
--datafile file
Specify the name of the file containing metadata about your classes. Default value: "./cobertura.ser".
--line 0..100
Specify the minimum acceptable line coverage rate needed by each class. This should be an integer value between 0 and 100.
Default value is 0.
--regex regex:branchrate:linerate
For finer grained control, you can optionally specify minimum branch and line coverage rates for individual classes using any
number of regular expressions.
--packagebranch 0..100
Specify the minimum acceptable average branch coverage rate needed by each package. This should be an integer value between 0 and
100. Default value is 0.
--packageline 0..100
Specify the minimum acceptable average line coverage rate needed by each package. This should be an integer value between 0 and
100. Default value is 0.
--totalbranch 0..100
Specify the minimum acceptable average branch coverage rate needed by the project as a whole. This should be an integer value
between 0 and 100. Default value is 0.
--totalline 0..100
Specify the minimum acceptable average line coverage rate needed by the project as a whole. This should be an integer value
between 0 and 100. Default value is 0.
SEE ALSO
junit(1), cobertura-instrument(1), cobertura-report(1), cobertura-merge(1).
AUTHOR
This manual page was written by Miguel Landaeta <miguel@miguel.cc> for the Debian system (but may be used by others). Permission is
granted to copy, distribute and/or modify this document under the terms of the terms of GNU General Public License, Version 2 or any later
version published by the Free Software Foundation.
On Debian systems, the complete text of the GNU General Public License can be found in /usr/share/common-licenses/GPL.
COBERTURA-CHECK(1)