06-18-2015
As I said, "ATA transport failed" and "I/O error" mean that your disk is broken.
You can as well verify with format -> select the disk -> analyze -> read
And then see the Error count in iostat -E for "dad1" (the kernel driver name for the "c0t0d0" disk, you can do iostat -nE to see the other name).
BTW the geometry matches a 20 GB disk; it is normal that the last sectors.of a disk or partition are unused.
Get a new disk! Restore your data or start an installation from scratch.
This User Gave Thanks to MadeInGermany For This Post:
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hi,
when installing a piece of third part software I get the error "Bad magic number" at one point when it tries to use libraries from the bea tuxedo server. Am I correct that this means that the software is expecting 32bit while I'm on 64bit? Is there a way around it or can it only be solved... (5 Replies)
Discussion started by: rein
5 Replies
2. Solaris
I tried rebooting my Sun server just a few minutes ago and I got the following at boot:
--
Sun Fire 280R (UltraSPARC-III+) , No Keyboard
Copyright 1998-2002 Sun Microsystems, Inc. All rights reserved.
OpenBoot 4.5, 1024 MB memory installed, Serial #xxxxxxxxx
Ethernet address... (6 Replies)
Discussion started by: deckard
6 Replies
3. Filesystems, Disks and Memory
Dear All,
i have a SCSI hard disk drive i'm installing on it solaris 5 and the workstation is sun sparc, i made an image of this H.D using Norton Ghost 6, so i took off the SCSI H.D from the sun workstation and put it on a Compaq server then i booted the server from the Norton Ghost floppy disk... (0 Replies)
Discussion started by: wesweshahaha
0 Replies
4. UNIX for Advanced & Expert Users
Hello All,
(RHEL4)
Few weeks ago I had posted a message in this forum about the problem I had when I replaced my two scsi disks and tried rebuild raid1 array.
I somehow managed to up the system with working raid1 array.
But the main problem persisted..
i.e when I reboot the system, mounting... (0 Replies)
Discussion started by: ravinandan
0 Replies
5. Solaris
Hello All,
I m very new to this forum.
i m having SUN NETRA X1 server with 40 GB HDD (Seagate) & 128 MB RAM.
i m trying this server for SUN 10 Practise.
As i m installing SUN 9 /10 with CD ,its giving me error after OK propmt
***************************
#boot cdrom
or
#boot cdrom... (16 Replies)
Discussion started by: amrut_k
16 Replies
6. Solaris
Hello,
I'm brand new to Sun/Solaris.
I have a Sun Blade 150, with SunOS 5.8.
I wanted to make a backup to prevent future data loss, so I put the disk in a normal PC with Windows XP to try to make a backup with Norton Ghost, the disk was detected, but not the file volume, so I place the disk... (6 Replies)
Discussion started by: Resadija
6 Replies
7. Solaris
I'll keep it fairly straight forward. I work with a Solaris server and magically today it decided to take a dump on me. At first it give a long list of files that couldn't be acessed before terminating the boot process and returning to the 'ok' prompt. Booting in single-user mode allowed me to run... (4 Replies)
Discussion started by: Aon
4 Replies
8. Solaris
I have created 1 LUN.
1)LUN 00BB 200GB /dev/rdsk/c1t3d44
/dev/rdsk/c2t28d44
/dev/rdsk/c3t19d44
/dev/rdsk/c4t12d44
2) Already added the new entry into sd.conf and rebooted.
3) Already done these:
powercf –q
power config
4) power display dev=all
I can see the new Symmetrix device.... (1 Reply)
Discussion started by: sirius20d
1 Replies
9. Solaris
Is there a way to recover label?
I could install (sparc) Solaris again, but it would take a lot of time. (5 Replies)
Discussion started by: orange47
5 Replies
10. Solaris
So we have a new to us v240 server with no OS installed. It has an outdated version of OB and ALOM so before we install the OS we want to update both. We have a DVD with the latest OB patch burned on it.
We do the boot cdrom command but receive the Bad Magic Number Error. Does an OS need to... (2 Replies)
Discussion started by: dunkpancakes
2 Replies
LEARN ABOUT ULTRIX
disktab
disktab(5) File Formats Manual disktab(5)
Name
disktab - disk description file
Syntax
#include <disktab.h>
Description
The file is a simple data base that describes disk geometries and disk partition characteristics. The format is patterned after the termi-
nal data base. Entries in consist of a number of fields separated by colons (:). The first entry for each disk gives the names that are
known for the disk, separated by vertical bars (|). The last name given should be a long name fully identifying the disk.
The following list indicates the normal values stored for each disk entry:
Name Type Description
ns num Number of sectors per track
nt num Number of tracks per cylinder
nc num Total number of cylinders on the disk
ba num Block size for partition `a' (bytes)
bd num Block size for partition `d' (bytes)
be num Block size for partition `e' (bytes)
bf num Block size for partition `f' (bytes)
bg num Block size for partition `g' (bytes)
bh num Block size for partition `h' (bytes)
fa num Fragment size for partition `a' (bytes)
fd num Fragment size for partition `d' (bytes)
fe num Fragment size for partition `e' (bytes)
ff num Fragment size for partition `f' (bytes)
fg num Fragment size for partition `g' (bytes)
fh num Fragment size for partition `h' (bytes)
pa num Size of partition `a' in sectors
pb num Size of partition `b' in sectors
pc num Size of partition `c' in sectors
pd num Size of partition `d' in sectors
pe num Size of partition `e' in sectors
pf num Size of partition `f' in sectors
pg num Size of partition `g' in sectors
ph num Size of partition `h' in sectors
se num Sector size in bytes
ty str Type of disk (e.g. removable, winchester)
The entries can be automatically generated with the program.
Files
See Also
chpt(8), newfs(8)
disktab(5)