I'm signing off for the night but some other commands that may help you work through this are:
To clean up the device list:
To remove hardware:
To check currently available disks:
And you already are aware of luxadm. Please read the man pages before running any of the above to make sure they will help you and not hurt you.
---------- Post updated at 09:42 PM ---------- Previous update was at 09:38 PM ----------
And one other thing: if you are using powerpath, Veritas, or some other multipathing software you may need to update them before you can fully remove the device.
Last edited by rbatte1; 06-15-2015 at 09:48 AM..
Reason: Added CODE tags
I just installed IBMsdd on Solaris diver along with the patches recommended. I also installed 2 - 2Gigs qlogic fiber cards & the corresponding pkges for the cards.
What command can I use to scan this LUN disks from my Soalris servers. Solaris doen't seem to be seeing this disks presented on it.... (2 Replies)
Is there a limit to the number of LUNS that can be concatenated using Solaris Volume manager with Soft partitions?
I have worked with some AIX admins in the past and there was such a limitation therefore limiting the size the filesystem could grow to.
Is there such a limitation in Solaris 9... (6 Replies)
hi,
what are the steps to detect and configure a new attached lun in Solaris 10.
Is there any difference between cfgadm and luxadm command ?
rgds,
snjksh (5 Replies)
How to get LUN WWN (i.e LUN mapped from a storage box say Symmetrix or clariion) in Solaris. fcinfo command does give the Target port wwn but what i'm looking for is the LUN WWN. Any help is appreciated. (2 Replies)
Hello to all,
Actually, currently on my Solaris box, I've a LUN (5TB space) from a EMC storage which is working fine, and a partition with ZFS filesystem is created for that LUN. as further you'll see in the logs, the "c4t6006016053802E00E6A9196B6506E211d0s2" is the current configured LUN in the... (4 Replies)
Hi,
I've noticed that mpathadm states that one of our luns has no active paths:
/dev/rdsk/c6t60000970000298700009533031324333d0s2
Total Path Count: 4
Operational Path Count: 4
/dev/rdsk/c6t60000970000298700009533031333037d0s2
... (3 Replies)
Hi all, I have the following LUN which is showing OK with its two paths:
DEVICE PROPERTIES for disk: /dev/rdsk/c23t500507630A3BC579d123s2
Vendor: IBM
Product ID: 2107900
Revision: 3010
Serial Num: 75WB0114900
Unformatted capacity:... (13 Replies)
Discussion started by: ludiegu
13 Replies
8. Post Here to Contact Site Administrators and Moderators
Locale::Codes::LangVar(3pm) Perl Programmers Reference Guide Locale::Codes::LangVar(3pm)NAME
Locale::Codes::LangVar - standard codes for language variation identification
SYNOPSIS
use Locale::Codes::LangVar;
$lvar = code2langvar('acm'); # $lvar gets 'Mesopotamian Arabic'
$code = langvar2code('Mesopotamian Arabic'); # $code gets 'acm'
@codes = all_langvar_codes();
@names = all_langvar_names();
DESCRIPTION
The "Locale::Codes::LangVar" module provides access to standard codes used for identifying language variations, such as those as defined in
the IANA language registry.
Most of the routines take an optional additional argument which specifies the code set to use. If not specified, the default IANA language
registry codes will be used.
SUPPORTED CODE SETS
There are several different code sets you can use for identifying language variations. A code set may be specified using either a name, or
a constant that is automatically exported by this module.
For example, the two are equivalent:
$lvar = code2langvar('en','alpha-2');
$lvar = code2langvar('en',LOCALE_CODE_ALPHA_2);
The codesets currently supported are:
alpha
This is the set of alphanumeric codes from the IANA language registry, such as 'arevela' for Eastern Armenian.
This code set is identified with the symbol "LOCALE_LANGVAR_ALPHA".
This is the default code set.
ROUTINES
code2langvar ( CODE [,CODESET] )
langvar2code ( NAME [,CODESET] )
langvar_code2code ( CODE ,CODESET ,CODESET2 )
all_langvar_codes ( [CODESET] )
all_langvar_names ( [CODESET] )
Locale::Codes::LangVar::rename_langvar ( CODE ,NEW_NAME [,CODESET] )
Locale::Codes::LangVar::add_langvar ( CODE ,NAME [,CODESET] )
Locale::Codes::LangVar::delete_langvar ( CODE [,CODESET] )
Locale::Codes::LangVar::add_langvar_alias ( NAME ,NEW_NAME )
Locale::Codes::LangVar::delete_langvar_alias ( NAME )
Locale::Codes::LangVar::rename_langvar_code ( CODE ,NEW_CODE [,CODESET] )
Locale::Codes::LangVar::add_langvar_code_alias ( CODE ,NEW_CODE [,CODESET] )
Locale::Codes::LangVar::delete_langvar_code_alias ( CODE [,CODESET] )
These routines are all documented in the Locale::Codes::API man page.
SEE ALSO
Locale::Codes
The Locale-Codes distribution.
Locale::Codes::API
The list of functions supported by this module.
http://www.iana.org/assignments/language-subtag-registry
The IANA language subtag registry.
AUTHOR
See Locale::Codes for full author history.
Currently maintained by Sullivan Beck (sbeck@cpan.org).
COPYRIGHT
Copyright (c) 2011-2012 Sullivan Beck
This module is free software; you can redistribute it and/or modify it under the same terms as Perl itself.
perl v5.16.2 2012-10-11 Locale::Codes::LangVar(3pm)