I just installed IBMsdd on Solaris diver along with the patches recommended. I also installed 2 - 2Gigs qlogic fiber cards & the corresponding pkges for the cards.
What command can I use to scan this LUN disks from my Soalris servers. Solaris doen't seem to be seeing this disks presented on it.... (2 Replies)
Is there a limit to the number of LUNS that can be concatenated using Solaris Volume manager with Soft partitions?
I have worked with some AIX admins in the past and there was such a limitation therefore limiting the size the filesystem could grow to.
Is there such a limitation in Solaris 9... (6 Replies)
hi,
what are the steps to detect and configure a new attached lun in Solaris 10.
Is there any difference between cfgadm and luxadm command ?
rgds,
snjksh (5 Replies)
How to get LUN WWN (i.e LUN mapped from a storage box say Symmetrix or clariion) in Solaris. fcinfo command does give the Target port wwn but what i'm looking for is the LUN WWN. Any help is appreciated. (2 Replies)
Hello to all,
Actually, currently on my Solaris box, I've a LUN (5TB space) from a EMC storage which is working fine, and a partition with ZFS filesystem is created for that LUN. as further you'll see in the logs, the "c4t6006016053802E00E6A9196B6506E211d0s2" is the current configured LUN in the... (4 Replies)
Hi,
I've noticed that mpathadm states that one of our luns has no active paths:
/dev/rdsk/c6t60000970000298700009533031324333d0s2
Total Path Count: 4
Operational Path Count: 4
/dev/rdsk/c6t60000970000298700009533031333037d0s2
... (3 Replies)
Hi all, I have the following LUN which is showing OK with its two paths:
DEVICE PROPERTIES for disk: /dev/rdsk/c23t500507630A3BC579d123s2
Vendor: IBM
Product ID: 2107900
Revision: 3010
Serial Num: 75WB0114900
Unformatted capacity:... (13 Replies)
Discussion started by: ludiegu
13 Replies
8. Post Here to Contact Site Administrators and Moderators
install-solaris(1M)install-solaris(1M)NAME
install-solaris - install the Solaris operating system
SYNOPSIS
install-solaris
install-solaris invokes the Solaris Install program. Depending on graphical capability and available memory at the time of invocation,
install-solaris invokes either a text-based installer or a graphical installer.
The following minimum requirements for physical memory dictate which features are available during installation:
For SPARC machines:
128 MB
Minimum physical memory for all installation types
128 MB
Minimum physical memory required for windowing system
384 MB
Minimum physical memory required for graphical-based installation
For x86 machines:
256 MB
Minimum physical memory for all installation types
256 MB
Minimum physical memory required for windowing system
512 MB
Minimum physical memory required for graphical-based installation
In some cases, even if the minimum physical memory is present, available virtual memory after system startup can limit the number of fea-
tures available.
install-solaris exists only on the Solaris installation media (CD or DVD) and should be invoked only from there. Refer to the for more
details.
install-solaris allows installation of the operating system onto any standalone system. install-solaris loads the software available on the
installation media. Refer to the for disk space requirements.
Refer to the for more information on the various menus and selections.
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcdrom (Solaris instal- |
| |lation media) |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
pkginfo(1), install(1M), pkgadd(1M), attributes(5)
It is advisable to exit install-solaris by means of the exit options in the install-solaris menus.
23 Sep 2005 install-solaris(1M)