Sponsored Content
Full Discussion: SAN Migration question
Operating Systems HP-UX SAN Migration question Post 302946569 by BG_JrAdmin on Wednesday 10th of June 2015 10:53:11 AM
Old 06-10-2015
I think it's version 2? Does that make sense? I'm almost sure I am giving the correct output below.

Code:
# uname -r
B.11.23
# swlist -l bundle QPKBASE
# Initializing...
# Contacting target "hostname"...
#
# Target:  hostname:/
#

  QPKBASE       B.11.23.1012.086a Base Quality Pack Bundle for HP-UX 11i v2, December 2010

 

10 More Discussions You Might Find Interesting

1. HP-UX

SAN migration

Hi, I'm going to be involved in a migration of SAN islands to one big SAN. I've not worked with SANs before and I'm not sure how to approach this. I suspect the disk devices on the HP servers are going to change, when the EVA's and servers are plugged into this new Cisco 9509 switch. Any... (0 Replies)
Discussion started by: Hils
0 Replies

2. Solaris

Veritas Storage Question (Data Migration)

Using Solaris 10 with Veritas Storage Foundation running. I want to copy all contents from DISKA LUN1 to DISKB LUN2. What would be the command syntax to do this? (0 Replies)
Discussion started by: soupbone38
0 Replies

3. Solaris

Question regarding Zone Migration

I have a general question regarding Zone Migration. I have an older system that is currently running a zone configured with ProFTPD & SSL. If I want to migrate or clone that zone to another (much newer) system, will I still have to setup & configure ProFTPD & SSL on the new system? (3 Replies)
Discussion started by: em23
3 Replies

4. Red Hat

SAN/LVM question

Hey everyone. I am working on designing a logging solution for a deployment we have going out in a few months. Right now we have a single storage head end, connected via fibre to a SAN. Basically the plan is to create a number of smaller LUNs on the SAN, and then use LVM2 to handle concatenating... (5 Replies)
Discussion started by: msarro
5 Replies

5. HP-UX

SAN Migration of HP-UX hosts

Hello gurus, I am a SAN Admin - not very familiar with the HPUX administration - so need help with the steps in regards to the migration I need to do at my client place. Environment: Migrating from CX4 to VMAX - using OR/Hot Pull. Here are the steps I have put together - HPUX gurus please... (5 Replies)
Discussion started by: jps460
5 Replies

6. Solaris

Need Help On Solaris Cluster Steps For San Migration

I am going to do a SAN Array migration and need the sequence of steps required on the Solaris cluster before moving the old array luns to new array luns. Here are the steps and I need info on the bold points:( I might even be wrong on the sequence of steps please correct me if I am wrong) 1.... (0 Replies)
Discussion started by: sunshinedeepu
0 Replies

7. AIX

SAN Migration

Hi all, We are migrating our SAN storage from HSV360 to 3PAR. The system runs aix 6.1 version with HACMP. Please let me know what are requirements from OS side and how are the data copied to the new disks. (10 Replies)
Discussion started by: ElizabethPJ
10 Replies

8. Red Hat

Volume group not activated at boot after SAN migration

I have an IBM blade running RHEL 5.4 server, connected to two Hitachi SANs using common fibre cards & Brocade switches. It has two volume groups made from old SAN LUNs. The old SAN needs to be retired so we allocated LUNs from the new SAN, discovered the LUNs as multipath disks (4 paths) and grew... (4 Replies)
Discussion started by: rbatte1
4 Replies

9. AIX

AIX - FC Switch migration, SAN Migration question!

I'm New to AIX / VIOS We're doing a FC switch cutover on an ibm device, connected via SAN. How do I tell if one path to my remote disk is lost? (aix lvm) How do I tell when my link is down on my HBA port? Appreciate your help, very much! (4 Replies)
Discussion started by: BG_JrAdmin
4 Replies

10. Solaris

How to identify if disk is attached to SAN and assist in migration.?

I am working on VM host and collecting data to identify the type of storage attached to the server which will be migrated to VNX. it has one ldom created on it luxadm probe output --- No Network Array enclosures found in /dev/es Found Fibre Channel device(s): Node... (7 Replies)
Discussion started by: kpatel786
7 Replies
Module::Install::Bundle(3pm)				User Contributed Perl Documentation			      Module::Install::Bundle(3pm)

NAME
Module::Install::Bundle - Bundle distributions along with your distribution SYNOPSIS
Have your Makefile.PL read as follows: use inc::Module::Install; name 'Foo-Bar'; all_from 'lib/Foo/Bar.pm'; requires 'Baz' => '1.60'; # one of either: bundle 'Baz' => '1.60'; # OR: auto_bundle; WriteAll; DESCRIPTION
Module::Install::Bundle allows you to bundle a CPAN distribution within your distribution. When your end-users install your distribution, the bundled distribution will be installed along with yours, unless a newer version of the bundled distribution already exists on their local filesystem. While bundling will increase the size of your distribution, it has several benefits: Allows installation of bundled distributions when CPAN is unavailable Allows installation of bundled distributions when networking is unavailable Allows everything your distribution needs to be packaged in one place Bundling differs from auto-installation in that when it comes time to install, a bundled distribution will be installed based on the distribution bundled with your distribution, whereas with auto-installation the distibution to be installed will be acquired from CPAN and then installed. METHODS
o auto_bundle() Takes no arguments, will bundle every distribution specified by a "requires()". When you, as a module author, do a "perl Makefile.PL" the latest versions of the distributions to be bundled will be acquired from CPAN and placed in inc/BUNDLES/. o bundle($name, $version) Takes a list of key/value pairs specifying a distribution name and version number. When you, as a module author, do a perl Makefile.PL the distributions that you specified with "bundle()" will be acquired from CPAN and placed in inc/BUNDLES/. o bundle_deps($name, $version) Same as "bundle", except that all dependencies of the bundled modules are also detected and bundled. To use this function, you need to declare the minimum supported perl version first, like this: perl_version( '5.005' ); o auto_bundle_deps Same as "auto_bundle", except that all dependencies of the bundled modules are also detected and bundled. This function has the same constraints as bundle_deps. BUGS
Please report any bugs to (patches welcome): http://rt.cpan.org/NoAuth/ReportBug.html?Queue=Module-Install AUTHORS
Audrey Tang <autrijus@autrijus.org> Documentation by Adam Foxson <afoxson@pobox.com> COPYRIGHT
Copyright 2003, 2004, 2005 by Audrey Tang <autrijus@autrijus.org>. This program is free software; you can redistribute it and/or modify it under the same terms as Perl itself. perl v5.14.2 2012-03-01 Module::Install::Bundle(3pm)
All times are GMT -4. The time now is 10:07 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy