SAN Migration question Post: 302946569

10 More Discussions You Might Find Interesting

1. HP-UX

SAN migration

Hi, I'm going to be involved in a migration of SAN islands to one big SAN. I've not worked with SANs before and I'm not sure how to approach this. I suspect the disk devices on the HP servers are going to change, when the EVA's and servers are plugged into this new Cisco 9509 switch. Any...

2. Solaris

Veritas Storage Question (Data Migration)

Using Solaris 10 with Veritas Storage Foundation running. I want to copy all contents from DISKA LUN1 to DISKB LUN2. What would be the command syntax to do this?

3. Solaris

Question regarding Zone Migration

I have a general question regarding Zone Migration. I have an older system that is currently running a zone configured with ProFTPD & SSL. If I want to migrate or clone that zone to another (much newer) system, will I still have to setup & configure ProFTPD & SSL on the new system?

4. Red Hat

SAN/LVM question

Hey everyone. I am working on designing a logging solution for a deployment we have going out in a few months. Right now we have a single storage head end, connected via fibre to a SAN. Basically the plan is to create a number of smaller LUNs on the SAN, and then use LVM2 to handle concatenating...

5. HP-UX

SAN Migration of HP-UX hosts

Hello gurus, I am a SAN Admin - not very familiar with the HPUX administration - so need help with the steps in regards to the migration I need to do at my client place. Environment: Migrating from CX4 to VMAX - using OR/Hot Pull. Here are the steps I have put together - HPUX gurus please...

6. Solaris

Need Help On Solaris Cluster Steps For San Migration

I am going to do a SAN Array migration and need the sequence of steps required on the Solaris cluster before moving the old array luns to new array luns. Here are the steps and I need info on the bold points:( I might even be wrong on the sequence of steps please correct me if I am wrong) 1....

7. AIX

SAN Migration

Hi all, We are migrating our SAN storage from HSV360 to 3PAR. The system runs aix 6.1 version with HACMP. Please let me know what are requirements from OS side and how are the data copied to the new disks.

8. Red Hat

Volume group not activated at boot after SAN migration

I have an IBM blade running RHEL 5.4 server, connected to two Hitachi SANs using common fibre cards & Brocade switches. It has two volume groups made from old SAN LUNs. The old SAN needs to be retired so we allocated LUNs from the new SAN, discovered the LUNs as multipath disks (4 paths) and grew...

9. AIX

AIX - FC Switch migration, SAN Migration question!

I'm New to AIX / VIOS We're doing a FC switch cutover on an ibm device, connected via SAN. How do I tell if one path to my remote disk is lost? (aix lvm) How do I tell when my link is down on my HBA port? Appreciate your help, very much!

10. Solaris

How to identify if disk is attached to SAN and assist in migration.?

I am working on VM host and collecting data to identify the type of storage attached to the server which will be migrated to VNX. it has one ldom created on it luxadm probe output --- No Network Array enclosures found in /dev/es Found Fibre Channel device(s): Node...

LEARN ABOUT CENTOS

mkqdisk

mkqdisk(8)						      Quorum Disk Management							mkqdisk(8)

NAME

       mkqdisk - Cluster Quorum Disk Utility

WARNING

       Use of this command can cause the cluster to malfunction.

SYNOPSIS

       mkqdisk [-?|-h] | [-L] | [-f label] [-c device  -l label] [-d [-d ...]]

DESCRIPTION

       The mkqdisk command is used to create a new quorum disk or display existing quorum disks accessible from a given cluster node.

OPTIONS

       -c device -l label
	      Initialize  a new cluster quorum disk.  This will destroy all data on the given device.  If a cluster is currently using that device
	      as a quorum disk, the entire cluster will malfunction.  Do not run this on an active cluster  when  qdiskd  is  running.	 Only  one
	      device  on  the  SAN should ever have the given label; using multiple different devices is currently not supported (it is expected a
	      RAID array is used for quorum disk redundancy).  The label can be any textual string up to 127 characters - and is therefore  enough
	      space to hold a UUID created with uuidgen(1).

       -f label
	      Find the cluster quorum disk with the given label and display information about it.

       -L     Display information on all accessible cluster quorum disks.

       -d     Increase debugging level.  Specify multiple times for more information.  Currently, specifying more than twice has no effect.

SEE ALSO

       qdisk(5), qdiskd(8), uuidgen(1)

								     July 2006								mkqdisk(8)

10 More Discussions You Might Find Interesting

1. HP-UX

SAN migration

Discussion started by: Hils

2. Solaris

Veritas Storage Question (Data Migration)

Discussion started by: soupbone38

3. Solaris

Question regarding Zone Migration

Discussion started by: em23

4. Red Hat

SAN/LVM question

Discussion started by: msarro