Sponsored Content
Full Discussion: SAN Migration question
Operating Systems HP-UX SAN Migration question Post 302946512 by Peasant on Wednesday 10th of June 2015 12:05:33 AM
Old 06-10-2015
Is the HPUX in question v2 or v3 ?

If the answer is v3, the operation can be online, since on v3, every lun has a WWID.
Just do it port by port, rescan and check paths after each, should not be any issues.

If you want to do it offline, do a vgexport preview (to a file not actual export) of all volume groups on the system using SAN disks (just to be safe do it anyway in each scenario) and deactivate the volume group.

Since the VG info is actually written on disks, even if everything changes (disk names etc.) you will be able to import the volume group using a file you created earlier. There are also other methods (vgscan), but this one is most trivial.

Commands you will require are
scsimgr -> to check lunmap and paths before and after.
ioscan -> to rescan after port change.

This assumes you are using hpux native multipath, not other multipath solutions.
 

10 More Discussions You Might Find Interesting

1. HP-UX

SAN migration

Hi, I'm going to be involved in a migration of SAN islands to one big SAN. I've not worked with SANs before and I'm not sure how to approach this. I suspect the disk devices on the HP servers are going to change, when the EVA's and servers are plugged into this new Cisco 9509 switch. Any... (0 Replies)
Discussion started by: Hils
0 Replies

2. Solaris

Veritas Storage Question (Data Migration)

Using Solaris 10 with Veritas Storage Foundation running. I want to copy all contents from DISKA LUN1 to DISKB LUN2. What would be the command syntax to do this? (0 Replies)
Discussion started by: soupbone38
0 Replies

3. Solaris

Question regarding Zone Migration

I have a general question regarding Zone Migration. I have an older system that is currently running a zone configured with ProFTPD & SSL. If I want to migrate or clone that zone to another (much newer) system, will I still have to setup & configure ProFTPD & SSL on the new system? (3 Replies)
Discussion started by: em23
3 Replies

4. Red Hat

SAN/LVM question

Hey everyone. I am working on designing a logging solution for a deployment we have going out in a few months. Right now we have a single storage head end, connected via fibre to a SAN. Basically the plan is to create a number of smaller LUNs on the SAN, and then use LVM2 to handle concatenating... (5 Replies)
Discussion started by: msarro
5 Replies

5. HP-UX

SAN Migration of HP-UX hosts

Hello gurus, I am a SAN Admin - not very familiar with the HPUX administration - so need help with the steps in regards to the migration I need to do at my client place. Environment: Migrating from CX4 to VMAX - using OR/Hot Pull. Here are the steps I have put together - HPUX gurus please... (5 Replies)
Discussion started by: jps460
5 Replies

6. Solaris

Need Help On Solaris Cluster Steps For San Migration

I am going to do a SAN Array migration and need the sequence of steps required on the Solaris cluster before moving the old array luns to new array luns. Here are the steps and I need info on the bold points:( I might even be wrong on the sequence of steps please correct me if I am wrong) 1.... (0 Replies)
Discussion started by: sunshinedeepu
0 Replies

7. AIX

SAN Migration

Hi all, We are migrating our SAN storage from HSV360 to 3PAR. The system runs aix 6.1 version with HACMP. Please let me know what are requirements from OS side and how are the data copied to the new disks. (10 Replies)
Discussion started by: ElizabethPJ
10 Replies

8. Red Hat

Volume group not activated at boot after SAN migration

I have an IBM blade running RHEL 5.4 server, connected to two Hitachi SANs using common fibre cards & Brocade switches. It has two volume groups made from old SAN LUNs. The old SAN needs to be retired so we allocated LUNs from the new SAN, discovered the LUNs as multipath disks (4 paths) and grew... (4 Replies)
Discussion started by: rbatte1
4 Replies

9. AIX

AIX - FC Switch migration, SAN Migration question!

I'm New to AIX / VIOS We're doing a FC switch cutover on an ibm device, connected via SAN. How do I tell if one path to my remote disk is lost? (aix lvm) How do I tell when my link is down on my HBA port? Appreciate your help, very much! (4 Replies)
Discussion started by: BG_JrAdmin
4 Replies

10. Solaris

How to identify if disk is attached to SAN and assist in migration.?

I am working on VM host and collecting data to identify the type of storage attached to the server which will be migrated to VNX. it has one ldom created on it luxadm probe output --- No Network Array enclosures found in /dev/es Found Fibre Channel device(s): Node... (7 Replies)
Discussion started by: kpatel786
7 Replies
VGSCAN(8)						      System Manager's Manual							 VGSCAN(8)

NAME
vgscan - scan all disks for volume groups and build /etc/lvmtab and /etc/lvmtab.d/* which are the database for all other lvm commands. SYNOPSIS
vgscan [-d|--debug] [-f|--forcenumbers] [-h|--help] [-r|--remove_snapshots [VolumeGroupName]] [-v|--verbose] DESCRIPTION
vgscan scans all SCSI, (E)IDE disks, multiple devices and a bunch of other disk devives in the system for volume groups defined. OPTIONS -d, --debug Enables additional debugging output (if compiled with DEBUG). -f, --forcenumbers If used volume group and/or logical volume minor numbers are found during scan, replace them. This will potentially cause problems for NFS exported filesystems on logical volumes with changed numbers. -h, --help Print a usage message on standard output and exit successfully. -r, --remove_snapshots [VolumeGroupName] Remove all snapshot logical volumes from all or just the named volume group. -v, --verbose Display verbose information of vgscan's activities. Hint Put vgscan in one of your system startup scripts. This gives you an actual logical volume manager database before activating all volume groups by doing a "vgchange -ay". DIAGNOSTICS
vgscan returns an exit code of 0 for success and > 0 for error: 1 error reading physical volumes 2 error inserting vokume group name into lvmtab 3 no volume group(s) found 4 error creating lvmtab 5 no or not enough free device specials to store volume group in lvmtab 6 error storing VGDA on disk(s) 7 reused LV device number 8 error releasing snapshot logical volume 95 driver/module not in kernel 96 invalid I/O protocol version 97 error locking logical volume manager 99 invalid command line See also lvm(8), vgcreate(8), vgchange(8) AUTHOR
Heinz Mauelshagen <Linux-LVM@Sistina.com> Heinz Mauelshagen LVM TOOLS VGSCAN(8)
All times are GMT -4. The time now is 09:55 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy