With such a huge difference in timing, I would check if the network is happy. There is a chance that the network card and the other end (switch or other network card, depending how you have it connected) do not agree on the speed.
Have a look at the manual pages for ethtool
You might see the problem in the output of:-
.....adjusting for the appropriate ethernet card. There is quite a bit of output, but you really want to see very low discard values. Anything else suggests that there is a conflict.
You may need to confirm with the network team that all the hops in between are behaving correctly and that you are not getting throttled (quality/class of service) with a packet shaper or other load manager/balancer.
Hello Guru,
I am using a Pro*C program to prepare some reports
usaually the report file size is greater than 1GB.
But nowadays program is very slow.
I found out the program is taking much time to write data to file .....
is there any unix related reason to be slow down, the file writting... (2 Replies)
Hi I am trying to do the following:
run a command that looks at a binary file and formats it
find the first line that has what I am looking for (there will be multiple)
print the name of the file that has it
So I am running this but ti's not working
ls -ltr *20080612* | while read line... (3 Replies)
Hi
I want to split a file that has 'n' number of records into 16 small files.
Can some one suggest me how to do this using Unix script?
Thanks
rrkk (10 Replies)
I got the following info from this forum, in regards to configuring my
Solaris x86 to link to the Net:
# echo 192.168.0.1 > /etc/defaultrouter
# route add default 192.168.0.1
# echo nameserver 192.168.0.1 >> /etc/resolv.conf
# cp /etc/nsswitch.dns /etc/nsswitch.conf
So I did... (1 Reply)
Hi, I facing an NFS problem. I have machine1, which has diskA and diskB, and machine2, both are Mandriva 2009 Linux.
When I am on machine2 and NFS mount both diskA and diskB of machine1. Writing to diskA is very fast, but writing to diskB is very slow. I tried different mount rsize and wsize... (2 Replies)
Hi guys,
I am trying something. I wrote a simple shell program to test something where continuous while loop writes on a file over the nfs. The time taken to write "hello" 3000 times take about 10 sec which is not right. Ideally it should take fraction of seconds. If I write on the local disk, it... (1 Reply)
there are few nas shares that would be mounted on the local zone. should i add an entry into the add an entry in zone.xml file so that it gets mounted automatically when the zone gets rebooted? or whats the correct way to get it mounted automatically when the zone reboots (2 Replies)
Hi,
I am facing chgrp issue for a directory on a NAS mounted partation.
issue details :
user1 belongs to two groups grp1(primary) and grp2(secondary) not able to change directory group to secondary.
WORKING on /tmp
#mkdir /tmp/a
#ls -ld /tmp/a
drwxr-xr-x 2 user1 grp1 117 Mar 24... (7 Replies)
Dear friends,
I have been facing an issue with one of my red hat unix machine, suddenly lost to switch sudo users. My all colleagues lost to switch to access sudo users.
Then, we have realized its related to NAS issue which does not allowing to write the file. because of this we got so many... (1 Reply)
Discussion started by: Chand
1 Replies
LEARN ABOUT CENTOS
rlm_expr
rlm_expr(5) FreeRADIUS Module rlm_expr(5)NAME
rlm_expr - FreeRADIUS Module
DESCRIPTION
The rlm_expr module allows the server to perform limited mathematical calculations. This module is not called directly in any section, it
is invoked through the dynamic expansion of strings.
For example, some NAS boxes send a NAS-Port attribute which is a 32-bit number composed of port, card, and interface, all in different
bytes. To see these attributes split into pieces, you can have an entry in the 'users' file like:
DEFAULT
Vendor-Interface = `%{expr: %{NAS-Port} / (256 * 256)}`,
Vendor-Card = `%{expr: (%{NAS-Port} / 256) %% 256}`,
Vendor-Port = `%{expr: %{NAS-Port} %% 256}`
where the attributes Vendor-Interface, Vendor-Card, and Vendor-Port are attributes created by either you or a vendor-supplied dictionary.
The methematical operators supported by the expression module are:
+ addition
- subtraction
/ division
%% modulo remainder
* multiplication
& boolean AND
| boolean OR
() grouping of sub-expressions
NOTE: The modulo remainder operator is '%%', and not '%'. This is due to the '%' character being used as a special character for dynamic
translation.
NOTE: These operators do NOT have precedence. The parsing of the input string, and the calculation of the answer, is done strictly left to
right. If you wish to order the expressions, you MUST group them into sub-expression, as shown in the previous example.
All of the calculations are performed as unsigned 32-bit integers.
CONFIGURATION
modules {
...
expr {
}
...
}
...
instantiate {
...
expr
...
}
SECTIONS
instantiate
FILES
/etc/raddb/radiusd.conf
SEE ALSO radiusd(8), radiusd.conf(5)AUTHOR
Chris Parker, cparker@segv.org
5 February 2004 rlm_expr(5)