Sponsored Content
Operating Systems Solaris Qlogic 10G Ethernet adapter not working Post 302946348 by bentech4u on Monday 8th of June 2015 01:20:46 PM
Old 06-08-2015
Solaris 10. sparc

Not server is physically migrated and reconfigured with

Reboot -- -rv -mverbose

Card: Qle 8142
Switch : brocade
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

How to change the MAC adress in ethernet adapter for SUN

I have installed in the server a quad ethernet adapter, I'm using two interfaces with two different IP networks, both interfaces are connected to a switch, the switch report that is receiving the same MAC address in both ports so must of the times I have connectivity problems. Any idea to change... (1 Reply)
Discussion started by: mono673
1 Replies

2. Solaris

Ethernet Adapter Question

I have a Dual Boot system - XP with Solaris 10. I built the system from the ground up with different components and the Ethernet Card built into the Motherboard is a Marvell Yukon Gigabit Ethernet 10/100/1000 T-base, RJ-45 Copper. I am unable to go to the Web as the Ethernet Card is still not... (2 Replies)
Discussion started by: tubbyrana
2 Replies

3. Solaris

How to install ethernet adapter on Sun Sparc M4000

hi all, How to install onboard ethernet card on Sun SPARC M4000 server? (3 Replies)
Discussion started by: Tlg13team
3 Replies

4. Solaris

Solaris 10 - QLogic 4060C iSCSI adapter - multipathed (MPxIO)

System: Sun M3000 and M4000 OS: Solaris 10 (fully up to date with latest patches) iSCSI HBA: 2x QLE4060C (QLogic) In each system are 2 QLE4060C iSCSI adapters. I manage to set up both HBA's to connect to the LUNs on the SAN However I don't manage to enable multi-pathing. Made the... (4 Replies)
Discussion started by: sb008
4 Replies

5. AIX

Temporarily disabling unused ethernet adapter

Hi, In our AIX 5.2 server , we have one unused ethernet adapter which doesn't have cable connection . For this interface , we are getting alerts in errpt . Could you suggesthow to stop this alert ? And sametime i would like to keep this device in ODM . Is there... (1 Reply)
Discussion started by: sekarsamy
1 Replies

6. AIX

Setting up an Integrated Virtual Ethernet adapter

All I am trying allocate an IVE to an LPAR (not a VIO) running AIX 7.1. I am getting the error: HSCL068A Explanation Logical port can not be assigned to Logical Partition because this Logical Partition is not the promiscuous LPAR for the physical port. Has anyone encountered this... (1 Reply)
Discussion started by: johnf
1 Replies

7. Red Hat

Ethernet Adapter not detected.

Hi, I have installed Oracle Enterprise Linux 5 in my PC. After the installation the Ethernet Card is not got detected. But I could able to get the details using the command lspci -a: 01:00.0 Ethernet controller: Attansic Technology Corp. L1 Gigabit Ethernet Adapter (rev b0). But I could... (4 Replies)
Discussion started by: chidhu.anu
4 Replies

8. Hardware

Need Sun 10-Gigabit Ethernet Adapter CD or ixge driver

Hi, Does anybody have a "Sun 10-Gigabit Ethernet Adapter installation CD" or driver ixge for Sun 10-Gigabit Ethernet PCI-X adapter? I need it but can't find it anywhere. So if you know where I can download it or purchase it, please let me know. (Already tried Oracle's website, don't have it) ... (5 Replies)
Discussion started by: Lhao
5 Replies

9. AIX

How to check the ethernet status for vlan and lhea adapter in client servers?

Hi Techies, I have a doubt. ent0 Available Logical Host Ethernet Port (lp-hea) ent1 Available Logical Host Ethernet Port (lp-hea) ent2 Available Logical Host Ethernet Port (lp-hea) ent3 Available Logical Host Ethernet Port (lp-hea) ent4 Available... (4 Replies)
Discussion started by: jayadeava
4 Replies

10. Red Hat

Red Hat 7 cannot recognize ethernet adapter

Hello community, I have a Proliant HP DL380P with the following network adapters: NetXtreme BCM5719 Gigabit Ethernet PCIe (Ethernet 1Gb 4-port 331FLR Adapter) 82580 Gigabit Network Connection (NC365T 4-port Ethernet Server Adapter) I installed Red Hat 7.2 but it recognizes only the... (9 Replies)
Discussion started by: Lord Spectre
9 Replies
csx_DeregisterClient(9F)				   Kernel Functions for Drivers 				  csx_DeregisterClient(9F)

NAME
csx_DeregisterClient - remove client from Card Services list SYNOPSIS
#include <sys/pccard.h> int32_t csx_DeregisterClient(client_handle_t ch); INTERFACE LEVEL
Solaris DDI Specific (Solaris DDI) PARAMETERS
ch Client handle returned from csx_RegisterClient(9F). DESCRIPTION
This function removes a client from the list of registered clients maintained by Card Services. The Client Handle returned by csx_Register- Client(9F) is passed in the client_handle_t argument. The client must have returned all requested resources before this function is called. If any resources have not been released, CS_IN_USE is returned. RETURN VALUES
CS_SUCCESS Successful operation. CS_BAD_HANDLE Client handle is invalid. CS_IN_USE Resources not released by this client. CS_UNSUPPORTED_FUNCTION No PCMCIA hardware installed. CONTEXT
This function may be called from user or kernel context. SEE ALSO
csx_RegisterClient(9F) PC Card 95 Standard, PCMCIA/JEIDA WARNINGS
Clients should be prepared to receive callbacks until Card Services returns from this request successfully. SunOS 5.11 19 Jul 1996 csx_DeregisterClient(9F)
All times are GMT -4. The time now is 06:55 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy