05-28-2015
Hi everyone
KGB I have managed to create 2 AIX 6.1 VMs, as well as a VIOs server ( created it first). each has a rootvg of about 130GB in size , basically taking up one physical 136GB disk on the 8202..
.I have two virtual ethernet adapters going from VIOS to each VM .vm #1 works perfectly well, is networked and we're having no problems with it. AIX 6.1 VM #2 is unable to see the network.I have set up the DNS server with the hostname and the ipaddress ( 10.10.1.68,devrs8).
I have created add'l ethernet adapters on VIOS, rebooted it so they are 'seen' by LPAR #2, rebooted LPAR #2, and I've tried to configure ( on the AIX 6.1 OS) ,one and all at different times without any luck.they are there, they just don't like to ping any remote system.I can ping the above address I give it, or 127.0.0.1 but nothing else. def route has been set.
tried using ifconfig, smit, mktcpip, I even tried to use DHCP.no luck.even re-installed the OS to get a clean slate to work with, and I'm stuck at the same thing.
dns
10.10.1.6 10.10.1.7
IP=10.10.1.68
def route 10.10.1.1
netmask 255.0.0.0
any advice on what might be the cause?
10 More Discussions You Might Find Interesting
1. AIX
can i get a step b syep explanation in creating LPAR... i have searched for tutorials i couldn't find the right one.... (2 Replies)
Discussion started by: udtyuvaraj
2 Replies
2. AIX
Hi all,
I have the following configuration
2 ds3524 storage disk systems located over 2 locations
2 P720 server located over 2 locations
DS3524 are connected to san switch.
Each vio server has 1 fc adapter attached to a san switch.
per p720 server 2 virtual io servers. Vio 1 has 1 lun... (2 Replies)
Discussion started by: markiemark
2 Replies
3. AIX
hi guys,
i need to develop following setup for a customer:
high availability oracle database on aix7 and linux in 2 different LPAR using dual ps700 blande a ds3400 and HMC.
the question is, it is possible to have automatic vioc failover(aix,linux) when for example 1 vios goes down?
in... (6 Replies)
Discussion started by: gullio23
6 Replies
4. Solaris
Hi,
I am creating "LSOF" solaris package from solaris "source" files. I have compiled the source file and with that i created prototype file also. Then using pkgmk command i can make the package .
In the package i am having (pkginfo pkgmap reloc) two file and one directory respectively
But... (3 Replies)
Discussion started by: Kathirvel G
3 Replies
5. AIX
Hi all please give me a link for IBM PowerVM (4 Replies)
Discussion started by: babinlonston
4 Replies
6. Windows & DOS: Issues & Discussions
Hello everyone,
I've been attempting to make a program which creates user accounts from a file which contains the usernames required. It also checks if the directory of the username exists in the C:\Users directory and then is going to give the option to delete the directory, or rename it, this... (1 Reply)
Discussion started by: charlieabee
1 Replies
7. AIX
Some simple questions about Intellistation 285 and powervm.
I want to learn AIX,so i will buy an used I285 from ebay.
1)Will support aix 7.1?
2)Is powervm avaliable?Where to download or buy it?
Thanks (3 Replies)
Discussion started by: Linusolaradm1
3 Replies
8. AIX
There can be configurations in IBM Server wherein a
standalone partition is created on some supported IBM Server
Or
A VIOS - VIOC LPARs created.
Now in both cases they are lpars. But if I want to differentiate b/w a standalone LPAR vs an VIOC LPAR how can I do..?
On a... (2 Replies)
Discussion started by: Manish00712
2 Replies
9. AIX
Hello,
POWER7 machine.
4 x 1Gbit port ethernet adapter is dedicated to vios. 8023ad etherchannel is created using those 4 ports. Etherchannel adapter is shared to lpars using SEA.
If I test network performance directly from vios partition (using iperf) I'm geting nice 4Gbit throughput. But if... (3 Replies)
Discussion started by: vilius
3 Replies
10. AIX
Hello,
After installing on P6 which is POWERVM IVM VIOS enabled (VET CODE D21C77ACD9229817CA1F00002C10004164 )
i get this message
"I/O hosting requires a hosting partition - boot not permitted".
HMC was connected to the machine
then HMC was removed through ASMI
Searching on... (2 Replies)
Discussion started by: filosophizer
2 Replies
LEARN ABOUT OPENSOLARIS
sbp
SBP(4) BSD Kernel Interfaces Manual SBP(4)
NAME
sbp -- Serial Bus Protocol 2 (SBP-2) Mass Storage Devices driver
SYNOPSIS
kldload firewire
kldload cam
kldload sbp
or
device sbp
device firewire
device scbus
device da
device cd
device pass
DESCRIPTION
The sbp driver provides support for SBP-2 devices that attach to the FireWire (IEEE 1394) port. It should work with SBP-2 devices which the
CAM layer supports, for example, HDDs, CDROM drives and DVD drives.
Some users familiar with umass(4) might wonder why the device is not detached at the CAM layer when the device is unplugged. It is detached
only if the device has not been plugged again during several bus resets. This is for preventing to detach an active file system even when
the device cannot be probed correctly for some reason after a bus reset or when the device is temporary disconnected because the user changes
the bus topology. If you want to force to detach the device, run ``fwcontrol -r'' several times or set hw.firewire.hold_count=0 by
sysctl(1).
Some (broken) HDDs do not work well with tagged queuing. If you have problems with such drives, try ``camcontrol [device id] tags -N 1'' to
disable tagged queuing.
SEE ALSO
cam(4), firewire(4), camcontrol(8), fwcontrol(8), kldload(8), sysctl(8)
AUTHORS
The sbp driver was written by Katsushi Kobayashi and Hidetoshi Shimokawa.
This manual page was written by Katsushi Kobayashi.
BSD
May 20, 2002 BSD