05-26-2015
Replacing the wifi card in your laptop probably isn't an option. Most laptops are programmed to freak out and refuse to boot if you do so, due to FCC regulations. Weird workarounds like disconnecting the detect pin until it boots have been done, but won't work with modern PCIE cards as far as I know.
Using a USB or other kind of external card is okay of course.
10 More Discussions You Might Find Interesting
1. AIX
I have an LPAR in a P5 machine which has been setup in an HACMP cluster. The person who set it up allocated the wrong network adapter (en) to the persistent network. For the life of me I cannot find where I can re-assign this adapter. Anyone able to help me as I am tearing my hair out and do not... (1 Reply)
Discussion started by: johnf
1 Replies
2. AIX
hello
i've need to change network adapter on machine H80 aix 4.3.3 hacmp ( ent0 )
what i need to do after the new adapter installed on the machine?
thanks
best regards
ariec (1 Reply)
Discussion started by: ariec
1 Replies
3. AIX
When I configure two VIO Servers, VIOS1 used to ping its gateway, after I configured second VIOS2, VIOS1 cannpt ping its gateway, when I run this command:
entstat -all ent#|grep -i priority
Priority: 5 Active: False
How to make Active to True? (1 Reply)
Discussion started by: rainbow_bean
1 Replies
4. UNIX for Dummies Questions & Answers
Hi All,
I am new here - this is my first post.
I have installed Solaris 10 5/09 on my Dell M6300. The install went well, but the Dell's onboard network card is the Broadcom BCM5756ME Gigabit Ethernet - and sadly no Solaris driver exists for it. The Solaris 10 install just jumped by the... (1 Reply)
Discussion started by: soulmerchant
1 Replies
5. IP Networking
Hi All,
Sorry if this is not the correct forum to answer.
But hope somebody can help me...
For these two types of network adapter:
Intel(R) PRO/1000 MT Server Adapter
Intel(R) PRO/1000 MT Dual Port Network Adapter
How many IP addresses can be configured on it at the same time?
System... (3 Replies)
Discussion started by: wilsonSurya
3 Replies
6. IP Networking
i have wireless usb adapter rtl8187 from micromax company
my proplem is the signal is very weak and i cannot open website
can i increase the signal ?
iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
wmaster0 no wireless extensions.
wlan0... (5 Replies)
Discussion started by: rsd220
5 Replies
7. UNIX for Dummies Questions & Answers
Hi All
I P2Vd a Unixware 7.1.4 box with VMWare Vsphere. I try to add a network adapter under Network Configuration Manager and it comes up with the error attached.
I've added a virtual adapter using the "E1000" option. It detects both the AMD PCI NET and E1000 virtual adapters under Network... (8 Replies)
Discussion started by: flashinwrx
8 Replies
8. UNIX for Dummies Questions & Answers
Hi all, I got sort of a task to do. I have to write in C "simulated network driver". What does it mean?
- It has to run on all network adapters
- It has to be as simple as it can be
- It has to run on all linux distributions (or at least most of them)
- It does not have to run a network... (4 Replies)
Discussion started by: Chrisdot
4 Replies
9. Hardware
How do I configure my wireless adapter to access the internet? I am running PCLinuxOS 2010. (0 Replies)
Discussion started by: ryan352333
0 Replies
10. SCO
hi .I've installed an operating system SCO in HP Z400 and network cards ZyXEL model FN312 with Chipset RTL8139D put it on .network card installed but do not display network card with command ifconfig -a in list and just show loopback.
show message :
dlpid:unable to open network adapter driver... (14 Replies)
Discussion started by: moein.mojtaba
14 Replies
LEARN ABOUT CENTOS
nm-connection-editor
NM-CONNECTION-EDITOR(1) General Commands Manual NM-CONNECTION-EDITOR(1)
NAME
nm-connection-editor - network connection editor for NetworkManager
SYNOPSIS
nm-connection-editor [ OPTIONS ]
DESCRIPTION
nm-connection-editor is a GTK-based application to add, remove, and modify network connections stored by NetworkManager. NetworkManager
must be running for any network connections to be added, removed, or modified.
OPTIONS
-t, --type=<type>
Type of connection to create or show. Values are NetworkManager setting names, eg "802-3-ethernet", "802-11-wireless", "bridge",
"bond", "wimax", "infiniband", "vlan", etc. Does nothing if --create or --show is not given.
-s, --show
Expand or collapse the network list to highlight the network connection type given by --type.
-c, --create
Create a new connection of the type given by --type and allow the user to modify connection details.
-e, --edit=<uuid>
Show the network connection edit window for the connection of the given UUID.
SEE ALSO
nmcli(1), NetworkManager(8), nm-applet(1).
15 February 2013 NM-CONNECTION-EDITOR(1)