Sponsored Content
Special Forums Hardware Problematic RTL8188EE Wireless Network Adapter Post 302945154 by Corona688 on Tuesday 26th of May 2015 04:25:24 PM
Old 05-26-2015
Replacing the wifi card in your laptop probably isn't an option. Most laptops are programmed to freak out and refuse to boot if you do so, due to FCC regulations. Weird workarounds like disconnecting the detect pin until it boots have been done, but won't work with modern PCIE cards as far as I know.

Using a USB or other kind of external card is okay of course.
 

10 More Discussions You Might Find Interesting

1. AIX

hacmp network adapter re-define

I have an LPAR in a P5 machine which has been setup in an HACMP cluster. The person who set it up allocated the wrong network adapter (en) to the persistent network. For the life of me I cannot find where I can re-assign this adapter. Anyone able to help me as I am tearing my hair out and do not... (1 Reply)
Discussion started by: johnf
1 Replies

2. AIX

change network adapter

hello i've need to change network adapter on machine H80 aix 4.3.3 hacmp ( ent0 ) what i need to do after the new adapter installed on the machine? thanks best regards ariec (1 Reply)
Discussion started by: ariec
1 Replies

3. AIX

How to active this network adapter?

When I configure two VIO Servers, VIOS1 used to ping its gateway, after I configured second VIOS2, VIOS1 cannpt ping its gateway, when I run this command: entstat -all ent#|grep -i priority Priority: 5 Active: False How to make Active to True? (1 Reply)
Discussion started by: rainbow_bean
1 Replies

4. UNIX for Dummies Questions & Answers

External Network Adapter for Solaris 10

Hi All, I am new here - this is my first post. I have installed Solaris 10 5/09 on my Dell M6300. The install went well, but the Dell's onboard network card is the Broadcom BCM5756ME Gigabit Ethernet - and sadly no Solaris driver exists for it. The Solaris 10 install just jumped by the... (1 Reply)
Discussion started by: soulmerchant
1 Replies

5. IP Networking

Maximum IP Address Configured on Intel Network Adapter

Hi All, Sorry if this is not the correct forum to answer. But hope somebody can help me... For these two types of network adapter: Intel(R) PRO/1000 MT Server Adapter Intel(R) PRO/1000 MT Dual Port Network Adapter How many IP addresses can be configured on it at the same time? System... (3 Replies)
Discussion started by: wilsonSurya
3 Replies

6. IP Networking

my wireless usb adapter connect to net but the signal is very weak

i have wireless usb adapter rtl8187 from micromax company my proplem is the signal is very weak and i cannot open website can i increase the signal ? iwconfig lo no wireless extensions. eth0 no wireless extensions. wmaster0 no wireless extensions. wlan0... (5 Replies)
Discussion started by: rsd220
5 Replies

7. UNIX for Dummies Questions & Answers

SCO Unixware 7.1.4 Network Adapter Error

Hi All I P2Vd a Unixware 7.1.4 box with VMWare Vsphere. I try to add a network adapter under Network Configuration Manager and it comes up with the error attached. I've added a virtual adapter using the "E1000" option. It detects both the AMD PCI NET and E1000 virtual adapters under Network... (8 Replies)
Discussion started by: flashinwrx
8 Replies

8. UNIX for Dummies Questions & Answers

Simulated driver for Network Interface Adapter

Hi all, I got sort of a task to do. I have to write in C "simulated network driver". What does it mean? - It has to run on all network adapters - It has to be as simple as it can be - It has to run on all linux distributions (or at least most of them) - It does not have to run a network... (4 Replies)
Discussion started by: Chrisdot
4 Replies

9. Hardware

Configuring a D-Link DWA-130 Wireless Adapter

How do I configure my wireless adapter to access the internet? I am running PCLinuxOS 2010. (0 Replies)
Discussion started by: ryan352333
0 Replies

10. SCO

Can not recognize network adapter SCO UNIX in HP z400

hi .I've installed an operating system SCO in HP Z400 and network cards ZyXEL model FN312 with Chipset RTL8139D put it on .network card installed but do not display network card with command ifconfig -a in list and just show loopback. show message : dlpid:unable to open network adapter driver... (14 Replies)
Discussion started by: moein.mojtaba
14 Replies
DAIC(4) 						   BSD Kernel Interfaces Manual 						   DAIC(4)

NAME
daic -- isdn4bsd driver for EICON.Diehl active ISDN cards SYNOPSIS
daic0 at isa? iomem 0xd8000 irq 10 DESCRIPTION
The daic driver supports the old Diehl active cards: S, SX, SXn, SCOM and QUADRO. For a QUADRO card, the driver will detect the board type and use all four ports, each attached as a controller of its own to the isdn4bsd system, which can be listed using the daicctl utility. The daic driver interfaces the ISDN card to the ISDN4BSD kernel subsystem. All lower layer ISDN control is handled by the card. This should allow you to run any national ISDN protocol delivered by EICON.Diehl for your card, but the driver has only been tested with the DSS1 proto- col and some parts of the cards interface are ISDN protocol dependent. The daic driver is written to conform to the software interface documented by Diehl in their ISDN-Karten Benutzerhandbuch from 1992. MICROCODE DOWNLOAD
Every active card needs its own operating software before it can work. You have to download this to the card before using it with isdn4bsd. Use the daicctl utility to do this, i.e. call daicctl -d te_etsi.sx 1 to download the file te_etsi.sx to controller number 1. Use daicctl -l to list all available controllers (and ports). You have to select the correct ISDN protocol file for your ISDN interface, see the Diehl docu- mentation for details. The cards bootstrap process involves another file, which is independent of the card type you use and the protocol you run. It is called download.bin in current versions of the Diehl software distribution and has to be copied to the kernel compile directory under dev/microcode/daic and converted into a header file used when compiling the kernel by running make in that directory. Your kernel compile will fail and remind you of this if you forget to do this. Due to copyright restrictions we cannot distribute the driver with this file inte- grated. But if you own a card, you do have the file (or can get it from the Diehl web server). SEE ALSO
daicctl(1) BUGS
The driver is not yet finished. BSD
January 30, 1998 BSD
All times are GMT -4. The time now is 11:04 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy