I do believe that I saw something while going through the journal errors about the bios... I need to go back and look at it again.
Thank you very much for the reply!
---------- Post updated at 12:09 PM ---------- Previous update was at 09:12 AM ----------
After a reboot I could get the the wifi interface to go up and down and it was able to reconnect as required in spite of the following errors...
So, it definitely looks like a standby process specifically turning off the wifi card and the resume process either cant or doesn't turn it back on...
---------- Post updated at 12:21 PM ---------- Previous update was at 12:09 PM ----------
BTW I did try to change the parameters on the modules and switch the power control to software controlled on; but I could not get the hardware control to turn off...
I now have a file in /etc/modprobe.d that contains those entries so that they are effective every boot.
I think I will try setting debug to 5 and the MSI parameter to 0 and trying again....
I have an LPAR in a P5 machine which has been setup in an HACMP cluster. The person who set it up allocated the wrong network adapter (en) to the persistent network. For the life of me I cannot find where I can re-assign this adapter. Anyone able to help me as I am tearing my hair out and do not... (1 Reply)
hello
i've need to change network adapter on machine H80 aix 4.3.3 hacmp ( ent0 )
what i need to do after the new adapter installed on the machine?
thanks
best regards
ariec (1 Reply)
When I configure two VIO Servers, VIOS1 used to ping its gateway, after I configured second VIOS2, VIOS1 cannpt ping its gateway, when I run this command:
entstat -all ent#|grep -i priority
Priority: 5 Active: False
How to make Active to True? (1 Reply)
Hi All,
I am new here - this is my first post.
I have installed Solaris 10 5/09 on my Dell M6300. The install went well, but the Dell's onboard network card is the Broadcom BCM5756ME Gigabit Ethernet - and sadly no Solaris driver exists for it. The Solaris 10 install just jumped by the... (1 Reply)
Hi All,
Sorry if this is not the correct forum to answer.
But hope somebody can help me...
For these two types of network adapter:
Intel(R) PRO/1000 MT Server Adapter
Intel(R) PRO/1000 MT Dual Port Network Adapter
How many IP addresses can be configured on it at the same time?
System... (3 Replies)
i have wireless usb adapter rtl8187 from micromax company
my proplem is the signal is very weak and i cannot open website
can i increase the signal ?
iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
wmaster0 no wireless extensions.
wlan0... (5 Replies)
Hi All
I P2Vd a Unixware 7.1.4 box with VMWare Vsphere. I try to add a network adapter under Network Configuration Manager and it comes up with the error attached.
I've added a virtual adapter using the "E1000" option. It detects both the AMD PCI NET and E1000 virtual adapters under Network... (8 Replies)
Hi all, I got sort of a task to do. I have to write in C "simulated network driver". What does it mean?
- It has to run on all network adapters
- It has to be as simple as it can be
- It has to run on all linux distributions (or at least most of them)
- It does not have to run a network... (4 Replies)
hi .I've installed an operating system SCO in HP Z400 and network cards ZyXEL model FN312 with Chipset RTL8139D put it on .network card installed but do not display network card with command ifconfig -a in list and just show loopback.
show message :
dlpid:unable to open network adapter driver... (14 Replies)
Discussion started by: moein.mojtaba
14 Replies
LEARN ABOUT PHP
putctl
putctl(9F) Kernel Functions for Drivers putctl(9F)NAME
putctl - send a control message to a queue
SYNOPSIS
#include <sys/stream.h>
int putctl(queue_t *q, int type);
INTERFACE LEVEL
Architecture independent level 1 (DDI/DKI).
PARAMETERS
q Queue to which the message is to be sent.
type Message type (must be control, not data type).
DESCRIPTION
putctl() tests the type argument to make sure a data type has not been specified, and then attempts to allocate a message block. putctl()
fails if type is M_DATA, M_PROTO, or M_PCPROTO, or if a message block cannot be allocated. If successful, putctl() calls the put(9E)
routine of the queue pointed to by q with the newly allocated and initialized messages.
RETURN VALUES
On success, 1 is returned. If type is a data type, or if a message block cannot be allocated, 0 is returned.
CONTEXT
putctl() can be called from user or interrupt context.
EXAMPLES
Example 1: Using putctl()
The send_ctl() routine is used to pass control messages downstream. M_BREAK messages are handled with putctl() (line 11). putctl1(9F)
(line 16) is used for M_DELAY messages, so that parm can be used to specify the length of the delay. In either case, if a message block
cannot be allocated a variable recording the number of allocation failures
is incremented (lines 12, 17). If an invalid message type is detected, cmn_err(9F) panics the system (line 21).
1 void
2 send_ctl(wrq, type, parm)
3 queue_t *wrq;
4 uchar_t type;
5 uchar_t parm;
6 {
7 extern int num_alloc_fail;
8
9 switch (type) {
10 case M_BREAK:
11 if (!putctl(wrq->q_next, M_BREAK))
12 num_alloc_fail++;
13 break;
14
15 case M_DELAY:
16 if (!putctl1(wrq->q_next, M_DELAY, parm))
17 num_alloc_fail++;
18 break;
19
20 default:
21 cmn_err(CE_PANIC, "send_ctl: bad message type passed");
22 break;
23 }
24 }
SEE ALSO put(9E), cmn_err(9F), datamsg(9F), putctl1(9F), putnextctl(9F)
Writing Device Drivers
STREAMS Programming Guide
SunOS 5.10 11 Apr 1991 putctl(9F)