I do believe that I saw something while going through the journal errors about the bios... I need to go back and look at it again.
Thank you very much for the reply!
---------- Post updated at 12:09 PM ---------- Previous update was at 09:12 AM ----------
After a reboot I could get the the wifi interface to go up and down and it was able to reconnect as required in spite of the following errors...
So, it definitely looks like a standby process specifically turning off the wifi card and the resume process either cant or doesn't turn it back on...
---------- Post updated at 12:21 PM ---------- Previous update was at 12:09 PM ----------
BTW I did try to change the parameters on the modules and switch the power control to software controlled on; but I could not get the hardware control to turn off...
I now have a file in /etc/modprobe.d that contains those entries so that they are effective every boot.
I think I will try setting debug to 5 and the MSI parameter to 0 and trying again....
I have an LPAR in a P5 machine which has been setup in an HACMP cluster. The person who set it up allocated the wrong network adapter (en) to the persistent network. For the life of me I cannot find where I can re-assign this adapter. Anyone able to help me as I am tearing my hair out and do not... (1 Reply)
hello
i've need to change network adapter on machine H80 aix 4.3.3 hacmp ( ent0 )
what i need to do after the new adapter installed on the machine?
thanks
best regards
ariec (1 Reply)
When I configure two VIO Servers, VIOS1 used to ping its gateway, after I configured second VIOS2, VIOS1 cannpt ping its gateway, when I run this command:
entstat -all ent#|grep -i priority
Priority: 5 Active: False
How to make Active to True? (1 Reply)
Hi All,
I am new here - this is my first post.
I have installed Solaris 10 5/09 on my Dell M6300. The install went well, but the Dell's onboard network card is the Broadcom BCM5756ME Gigabit Ethernet - and sadly no Solaris driver exists for it. The Solaris 10 install just jumped by the... (1 Reply)
Hi All,
Sorry if this is not the correct forum to answer.
But hope somebody can help me...
For these two types of network adapter:
Intel(R) PRO/1000 MT Server Adapter
Intel(R) PRO/1000 MT Dual Port Network Adapter
How many IP addresses can be configured on it at the same time?
System... (3 Replies)
i have wireless usb adapter rtl8187 from micromax company
my proplem is the signal is very weak and i cannot open website
can i increase the signal ?
iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
wmaster0 no wireless extensions.
wlan0... (5 Replies)
Hi All
I P2Vd a Unixware 7.1.4 box with VMWare Vsphere. I try to add a network adapter under Network Configuration Manager and it comes up with the error attached.
I've added a virtual adapter using the "E1000" option. It detects both the AMD PCI NET and E1000 virtual adapters under Network... (8 Replies)
Hi all, I got sort of a task to do. I have to write in C "simulated network driver". What does it mean?
- It has to run on all network adapters
- It has to be as simple as it can be
- It has to run on all linux distributions (or at least most of them)
- It does not have to run a network... (4 Replies)
hi .I've installed an operating system SCO in HP Z400 and network cards ZyXEL model FN312 with Chipset RTL8139D put it on .network card installed but do not display network card with command ifconfig -a in list and just show loopback.
show message :
dlpid:unable to open network adapter driver... (14 Replies)
Discussion started by: moein.mojtaba
14 Replies
LEARN ABOUT CENTOS
modinfo
MODINFO(8) modinfo MODINFO(8)NAME
modinfo - Show information about a Linux Kernel module
SYNOPSIS
modinfo [-0] [-F field] [-k kernel] [modulename|filename...]
modinfo -V
modinfo -h
DESCRIPTION
modinfo extracts information from the Linux Kernel modules given on the command line. If the module name is not a filename, then the
/lib/modules/version directory is searched, as is also done by modprobe(8) when loading kernel modules.
modinfo by default lists each attribute of the module in form fieldname : value, for easy reading. The filename is listed the same way
(although it's not really an attribute).
This version of modinfo can understand modules of any Linux Kernel architecture.
OPTIONS -V, --version
Print the modinfo version.
-F, --field
Only print this field value, one per line. This is most useful for scripts. Field names are case-insensitive. Common fields (which may
not be in every module) include author, description, license, parm, depends, and alias. There are often multiple parm, alias and
depends fields. The special field filename lists the filename of the module.
-b basedir, --basedir basedir
Root directory for modules, / by default.
-k kernel
Provide information about a kernel other than the running one. This is particularly useful for distributions needing to extract
information from a newly installed (but not yet running) set of kernel modules. For example, you wish to find which firmware files are
needed by various modules in a new kernel for which you must make an initrd/initramfs image prior to booting.
-0, --null
Use the ASCII zero character to separate field values, instead of a new line. This is useful for scripts, since a new line can
theoretically appear inside a field.
-a --author, -d --description, -l --license, -p --parameters, -n --filename
These are shortcuts for the --field flag's author, description, license, parm and filename arguments, to ease the transition from the
old modutils modinfo.
COPYRIGHT
This manual page originally Copyright 2003, Rusty Russell, IBM Corporation. Maintained by Jon Masters and others.
SEE ALSO modprobe(8)AUTHORS
Jon Masters <jcm@jonmasters.org>
Developer
Lucas De Marchi <lucas.demarchi@profusion.mobi>
Developer
kmod 07/02/2013 MODINFO(8)