---------- Post updated at 03:26 PM ---------- Previous update was at 02:28 PM ----------
I forgot to answer you question about the modules involved... ---------- Post updated at 03:38 PM ---------- Previous update was at 03:26 PM ----------
We'll I unloaded the driver stack prior to suspend.
Then I opened the lid of the laptop and ran:
It appears that it is not the driver stack that is causing the card to become disabled...
Maybe it the ACPI??
I did notice that the system log shows a notice that the generic ACPI should be replaced by a proprietary driver if available...
Thoughts?
Last edited by RogerBaran; 05-25-2015 at 05:56 PM..
I have an LPAR in a P5 machine which has been setup in an HACMP cluster. The person who set it up allocated the wrong network adapter (en) to the persistent network. For the life of me I cannot find where I can re-assign this adapter. Anyone able to help me as I am tearing my hair out and do not... (1 Reply)
hello
i've need to change network adapter on machine H80 aix 4.3.3 hacmp ( ent0 )
what i need to do after the new adapter installed on the machine?
thanks
best regards
ariec (1 Reply)
When I configure two VIO Servers, VIOS1 used to ping its gateway, after I configured second VIOS2, VIOS1 cannpt ping its gateway, when I run this command:
entstat -all ent#|grep -i priority
Priority: 5 Active: False
How to make Active to True? (1 Reply)
Hi All,
I am new here - this is my first post.
I have installed Solaris 10 5/09 on my Dell M6300. The install went well, but the Dell's onboard network card is the Broadcom BCM5756ME Gigabit Ethernet - and sadly no Solaris driver exists for it. The Solaris 10 install just jumped by the... (1 Reply)
Hi All,
Sorry if this is not the correct forum to answer.
But hope somebody can help me...
For these two types of network adapter:
Intel(R) PRO/1000 MT Server Adapter
Intel(R) PRO/1000 MT Dual Port Network Adapter
How many IP addresses can be configured on it at the same time?
System... (3 Replies)
i have wireless usb adapter rtl8187 from micromax company
my proplem is the signal is very weak and i cannot open website
can i increase the signal ?
iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
wmaster0 no wireless extensions.
wlan0... (5 Replies)
Hi All
I P2Vd a Unixware 7.1.4 box with VMWare Vsphere. I try to add a network adapter under Network Configuration Manager and it comes up with the error attached.
I've added a virtual adapter using the "E1000" option. It detects both the AMD PCI NET and E1000 virtual adapters under Network... (8 Replies)
Hi all, I got sort of a task to do. I have to write in C "simulated network driver". What does it mean?
- It has to run on all network adapters
- It has to be as simple as it can be
- It has to run on all linux distributions (or at least most of them)
- It does not have to run a network... (4 Replies)
hi .I've installed an operating system SCO in HP Z400 and network cards ZyXEL model FN312 with Chipset RTL8139D put it on .network card installed but do not display network card with command ifconfig -a in list and just show loopback.
show message :
dlpid:unable to open network adapter driver... (14 Replies)
Discussion started by: moein.mojtaba
14 Replies
LEARN ABOUT PHP
modules-load.d
MODULES-LOAD.D(5) modules-load.d MODULES-LOAD.D(5)NAME
modules-load.d - Configure kernel modules to load at boot
SYNOPSIS
/etc/modules-load.d/*.conf
/run/modules-load.d/*.conf
/usr/lib/modules-load.d/*.conf
DESCRIPTION systemd-modules-load.service(8) reads files from the above directories which contain kernel modules to load during boot in a static list.
Each configuration file is named in the style of /etc/modules-load.d/program.conf. Note that it is usually a better idea to rely on the
automatic module loading by PCI IDs, USB IDs, DMI IDs or similar triggers encoded in the kernel modules themselves instead of static
configuration like this. In fact, most modern kernel modules are prepared for automatic loading already.
CONFIGURATION FORMAT
The configuration files should simply contain a list of kernel module names to load, separated by newlines. Empty lines and lines whose
first non-whitespace character is # or ; are ignored.
CONFIGURATION DIRECTORIES AND PRECEDENCE
Configuration files are read from directories in /etc/, /run/, and /lib/, in order of precedence. Each configuration file in these
configuration directories shall be named in the style of filename.conf. Files in /etc/ override files with the same name in /run/ and
/lib/. Files in /run/ override files with the same name in /lib/.
Packages should install their configuration files in /lib/. Files in /etc/ are reserved for the local administrator, who may use this logic
to override the configuration files installed by vendor packages. All configuration files are sorted by their filename in lexicographic
order, regardless of which of the directories they reside in. If multiple files specify the same option, the entry in the file with the
lexicographically latest name will take precedence. It is recommended to prefix all filenames with a two-digit number and a dash, to
simplify the ordering of the files.
If the administrator wants to disable a configuration file supplied by the vendor, the recommended way is to place a symlink to /dev/null
in the configuration directory in /etc/, with the same filename as the vendor configuration file. If the vendor configuration file is
included in the initrd image, the image has to be regenerated.
EXAMPLE
Example 1. /etc/modules-load.d/virtio-net.conf example:
# Load virtio-net.ko at boot
virtio-net
SEE ALSO systemd(1), systemd-modules-load.service(8), systemd-delta(1), modprobe(8)systemd 237MODULES-LOAD.D(5)