---------- Post updated at 03:26 PM ---------- Previous update was at 02:28 PM ----------
I forgot to answer you question about the modules involved... ---------- Post updated at 03:38 PM ---------- Previous update was at 03:26 PM ----------
We'll I unloaded the driver stack prior to suspend.
Then I opened the lid of the laptop and ran:
It appears that it is not the driver stack that is causing the card to become disabled...
Maybe it the ACPI??
I did notice that the system log shows a notice that the generic ACPI should be replaced by a proprietary driver if available...
Thoughts?
Last edited by RogerBaran; 05-25-2015 at 05:56 PM..
I have an LPAR in a P5 machine which has been setup in an HACMP cluster. The person who set it up allocated the wrong network adapter (en) to the persistent network. For the life of me I cannot find where I can re-assign this adapter. Anyone able to help me as I am tearing my hair out and do not... (1 Reply)
hello
i've need to change network adapter on machine H80 aix 4.3.3 hacmp ( ent0 )
what i need to do after the new adapter installed on the machine?
thanks
best regards
ariec (1 Reply)
When I configure two VIO Servers, VIOS1 used to ping its gateway, after I configured second VIOS2, VIOS1 cannpt ping its gateway, when I run this command:
entstat -all ent#|grep -i priority
Priority: 5 Active: False
How to make Active to True? (1 Reply)
Hi All,
I am new here - this is my first post.
I have installed Solaris 10 5/09 on my Dell M6300. The install went well, but the Dell's onboard network card is the Broadcom BCM5756ME Gigabit Ethernet - and sadly no Solaris driver exists for it. The Solaris 10 install just jumped by the... (1 Reply)
Hi All,
Sorry if this is not the correct forum to answer.
But hope somebody can help me...
For these two types of network adapter:
Intel(R) PRO/1000 MT Server Adapter
Intel(R) PRO/1000 MT Dual Port Network Adapter
How many IP addresses can be configured on it at the same time?
System... (3 Replies)
i have wireless usb adapter rtl8187 from micromax company
my proplem is the signal is very weak and i cannot open website
can i increase the signal ?
iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
wmaster0 no wireless extensions.
wlan0... (5 Replies)
Hi All
I P2Vd a Unixware 7.1.4 box with VMWare Vsphere. I try to add a network adapter under Network Configuration Manager and it comes up with the error attached.
I've added a virtual adapter using the "E1000" option. It detects both the AMD PCI NET and E1000 virtual adapters under Network... (8 Replies)
Hi all, I got sort of a task to do. I have to write in C "simulated network driver". What does it mean?
- It has to run on all network adapters
- It has to be as simple as it can be
- It has to run on all linux distributions (or at least most of them)
- It does not have to run a network... (4 Replies)
hi .I've installed an operating system SCO in HP Z400 and network cards ZyXEL model FN312 with Chipset RTL8139D put it on .network card installed but do not display network card with command ifconfig -a in list and just show loopback.
show message :
dlpid:unable to open network adapter driver... (14 Replies)
Discussion started by: moein.mojtaba
14 Replies
LEARN ABOUT REDHAT
iwevent
IWEVENT(8) Linux Programmer's Manual IWEVENT(8)NAME
iwevent - Display Wireless Events generated by drivers and setting changes
SYNOPSIS
iwevent
DESCRIPTION
iwevent display Wireless Events received through the RTNetlink socket. Each line display the specific Wireless Event which describe what
has happened on the specified wireless interface.
This command doesn't take any arguments.
DISPLAY
There is two classes of Wireless Events.
The first class is events related to a change of wireless settings on the interface (typically done through iwconfig or a script calling
iwconfig). Only settings that could result in a disruption of connectivity are reported. The events currently reported are changing one of
the following setting :
Network ID
ESSID
Frequency
Mode
Encryption
All those events will be generated on all wireless interfaces by the kernel wireless subsystem (but only if the driver has been converted
to the new driver API).
The second class of events are events generated by the hardware, when something happens or a task has been finished. Those events include :
New Access Point/Cell address
The interface has joined a new Access Point or Ad-Hoc Cell, or lost its association with it. This is the same MAC address that is
reported by iwconfig.
Scan request completed
A scanning request has been completed, results of the scan are available (see iwlist).
Tx packet dropped
A packet directed at this address has been dropped because the interface believes this node doesn't answer anymore. An early indica-
tion that the node may have left the cell or gone out of range.
Custom driver event
Event specific to the driver. Please check the driver documentation.
Registered node
The interface has successfully registered a new wireless client/peer. Will be generated mostly when the interface act as an Access
Point (mode master).
Expired node
The registration of the client/peer on this interface has expired. Will be generated mostly when the interface act as an Access
Point (mode master).
Only some of those events will be generated on some wireless interfaces by the wireless driver, and their support depend on the specific
hardware/driver combination. Please refer to driver documentation for details.
AUTHOR
Jean Tourrilhes - jt@hpl.hp.com
SEE ALSO iwconfig(8), ifconfig(8), iwspy(8), iwpriv(8).
net-tools 25 January 2002 IWEVENT(8)