---------- Post updated at 03:26 PM ---------- Previous update was at 02:28 PM ----------
I forgot to answer you question about the modules involved... ---------- Post updated at 03:38 PM ---------- Previous update was at 03:26 PM ----------
We'll I unloaded the driver stack prior to suspend.
Then I opened the lid of the laptop and ran:
It appears that it is not the driver stack that is causing the card to become disabled...
Maybe it the ACPI??
I did notice that the system log shows a notice that the generic ACPI should be replaced by a proprietary driver if available...
Thoughts?
Last edited by RogerBaran; 05-25-2015 at 05:56 PM..
I have an LPAR in a P5 machine which has been setup in an HACMP cluster. The person who set it up allocated the wrong network adapter (en) to the persistent network. For the life of me I cannot find where I can re-assign this adapter. Anyone able to help me as I am tearing my hair out and do not... (1 Reply)
hello
i've need to change network adapter on machine H80 aix 4.3.3 hacmp ( ent0 )
what i need to do after the new adapter installed on the machine?
thanks
best regards
ariec (1 Reply)
When I configure two VIO Servers, VIOS1 used to ping its gateway, after I configured second VIOS2, VIOS1 cannpt ping its gateway, when I run this command:
entstat -all ent#|grep -i priority
Priority: 5 Active: False
How to make Active to True? (1 Reply)
Hi All,
I am new here - this is my first post.
I have installed Solaris 10 5/09 on my Dell M6300. The install went well, but the Dell's onboard network card is the Broadcom BCM5756ME Gigabit Ethernet - and sadly no Solaris driver exists for it. The Solaris 10 install just jumped by the... (1 Reply)
Hi All,
Sorry if this is not the correct forum to answer.
But hope somebody can help me...
For these two types of network adapter:
Intel(R) PRO/1000 MT Server Adapter
Intel(R) PRO/1000 MT Dual Port Network Adapter
How many IP addresses can be configured on it at the same time?
System... (3 Replies)
i have wireless usb adapter rtl8187 from micromax company
my proplem is the signal is very weak and i cannot open website
can i increase the signal ?
iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
wmaster0 no wireless extensions.
wlan0... (5 Replies)
Hi All
I P2Vd a Unixware 7.1.4 box with VMWare Vsphere. I try to add a network adapter under Network Configuration Manager and it comes up with the error attached.
I've added a virtual adapter using the "E1000" option. It detects both the AMD PCI NET and E1000 virtual adapters under Network... (8 Replies)
Hi all, I got sort of a task to do. I have to write in C "simulated network driver". What does it mean?
- It has to run on all network adapters
- It has to be as simple as it can be
- It has to run on all linux distributions (or at least most of them)
- It does not have to run a network... (4 Replies)
hi .I've installed an operating system SCO in HP Z400 and network cards ZyXEL model FN312 with Chipset RTL8139D put it on .network card installed but do not display network card with command ifconfig -a in list and just show loopback.
show message :
dlpid:unable to open network adapter driver... (14 Replies)
Discussion started by: moein.mojtaba
14 Replies
LEARN ABOUT OPENSOLARIS
wireless
WIRELESS(7) Linux Programmer's Manual WIRELESS(7)NAME
wireless - Wireless Tools and Wireless Extensions
SYNOPSIS
iwconfig
iwpriv -a
DESCRIPTION
The Wireless Extensions is an API allowing you manipulate Wireless LAN networking interfaces. It is composed of a variety of tools and
configuration files. It is documented in more detail in the Linux Wireless LAN Howto.
The Wireless Tools are used to change the configuration of wireless LAN networking interfaces on the fly, to get their current configura-
tion, to get statistics and diagnose them. They are described in their own man page, see below for references.
Wireless configuration is specific to each Linux distribution. This man page will contain in the future the configuration procedure for a
few common distributions. For the time being, check the file DISTRIBUTIONS.txt included with the Wireless Tools package.
DEBIAN 3.0
In Debian 3.0 (and later) you can configure wireless LAN networking devices using the network configuration tool ifupdown(8).
File : /etc/network/interfaces
Form : wireless-<function> <value>
wireless-essid Home
wireless-mode Ad-Hoc
See also :
/etc/network/if-pre-up.d/wireless-tools
/usr/share/doc/wireless-tools/README.Debian
SuSE 8.0
SuSE 8.0 (and later) has integrated wireless configuration in their network scripts.
Tool : Yast2
File : /etc/sysconfig/network/wireless
/etc/sysconfig/network/ifcfg-*
Form : WIRELESS_<function>=<value>
WIRELESS_ESSID="Home"
WIRELESS_MODE=Ad-Hoc
See also :
man ifup
info scpm
ORIGINAL PCMCIA SCRIPTS
If you are using the original configuration scripts from the Pcmcia package, you can use this method.
File : /etc/pcmcia/wireless.opts
Form : *,*,*,*)
ESSID="Home"
MODE="Ad-Hoc"
;;
See also :
/etc/pcmcia/wireless
File PCMCIA.txt part of Wireless Tools package
AUTHOR
Jean Tourrilhes - jt@hpl.hp.com
http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/
SEE ALSO iwconfig(8), iwlist(8), iwspy(8), iwpriv(8), iwevent(8).
wireless-tools 4 March 2004 WIRELESS(7)