Good Day All,
There are numerous results when searching google on this issue, however, none seem to have a solution.
I have read until my eyes bleed and banged my head on the table more than once!
I am hoping to resolve this issue -- or at least have a decent workaround.
It is a real pain not to be able to put my laptop in standby knowing that if I do, I will have to reboot to regain my wireless connectivity.
I have copied snippets from **lshw** which first shows what type of system we are dealing with and then the state that the
wireless adapter is left in after going into sleep mode.
Unloading and reloading the drivers, obviously, has no effect. The card stays disabled.
My question: Is there a way (via scripting or creating a small piece of executable code) to access the hardware, turn the wireless adapter back on,
and reload the drivers to regain connectivity without rebooting?
I am using Fedora 21 with the most recent kernel updates...
I can provide whatever other information that might be needed for this project very expeditiously.
Many people will be benefited by a workaround for this issue.
I have an LPAR in a P5 machine which has been setup in an HACMP cluster. The person who set it up allocated the wrong network adapter (en) to the persistent network. For the life of me I cannot find where I can re-assign this adapter. Anyone able to help me as I am tearing my hair out and do not... (1 Reply)
hello
i've need to change network adapter on machine H80 aix 4.3.3 hacmp ( ent0 )
what i need to do after the new adapter installed on the machine?
thanks
best regards
ariec (1 Reply)
When I configure two VIO Servers, VIOS1 used to ping its gateway, after I configured second VIOS2, VIOS1 cannpt ping its gateway, when I run this command:
entstat -all ent#|grep -i priority
Priority: 5 Active: False
How to make Active to True? (1 Reply)
Hi All,
I am new here - this is my first post.
I have installed Solaris 10 5/09 on my Dell M6300. The install went well, but the Dell's onboard network card is the Broadcom BCM5756ME Gigabit Ethernet - and sadly no Solaris driver exists for it. The Solaris 10 install just jumped by the... (1 Reply)
Hi All,
Sorry if this is not the correct forum to answer.
But hope somebody can help me...
For these two types of network adapter:
Intel(R) PRO/1000 MT Server Adapter
Intel(R) PRO/1000 MT Dual Port Network Adapter
How many IP addresses can be configured on it at the same time?
System... (3 Replies)
i have wireless usb adapter rtl8187 from micromax company
my proplem is the signal is very weak and i cannot open website
can i increase the signal ?
iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
wmaster0 no wireless extensions.
wlan0... (5 Replies)
Hi All
I P2Vd a Unixware 7.1.4 box with VMWare Vsphere. I try to add a network adapter under Network Configuration Manager and it comes up with the error attached.
I've added a virtual adapter using the "E1000" option. It detects both the AMD PCI NET and E1000 virtual adapters under Network... (8 Replies)
Hi all, I got sort of a task to do. I have to write in C "simulated network driver". What does it mean?
- It has to run on all network adapters
- It has to be as simple as it can be
- It has to run on all linux distributions (or at least most of them)
- It does not have to run a network... (4 Replies)
hi .I've installed an operating system SCO in HP Z400 and network cards ZyXEL model FN312 with Chipset RTL8139D put it on .network card installed but do not display network card with command ifconfig -a in list and just show loopback.
show message :
dlpid:unable to open network adapter driver... (14 Replies)