Sponsored Content
Operating Systems AIX PowerVM/lpar creation problems Post 302943985 by bakunin on Thursday 14th of May 2015 01:20:58 PM
Old 05-14-2015
dukessd is absolutely correct! You are doing it all wrong because you do not understand:

Quote:
Originally Posted by computron
in a nutshell, we have an 8202 with 6 internal 146GB drives, 128GB RAM, 6CPUs, PowerVM 'standard' licensing,4 internal NICs, plus two disk enclosures( g30,d24)
OK, but most critical: where are the (physical) SCSI adapters? The way you describe it you do not even have one and how are the disks supposed to be connected to the system, hm? dukessd said already that you probably have only one SCSI adapter and this is already taken by the first system you install.

Quote:
Originally Posted by computron
I'm familiar with AIX,linux,hp-ux,solaris, vmware esxi 4,5,6,etc. you mentioned that powerVM is really at the hardware level as opposed to having an OS installed, but I think you mean like what the older VmWare used to be
No, i meant what i said: Linux virtualisation is: take some hardware, install Linux, install some software (for instance "Openbox") on top, then create several instances of running Openbox-processes (aka "virtual machines"), then install some OS of your choice into each of these virtual machines.

IBM virtualisation is: connect the MS to the HMC, create some LPAR profiles and install into each LPAR an OS. The "HW-host-OS-virtualisation-software" part of a virtualised Linux system is all in hardware.




Quote:
Originally Posted by computron
I can configure #2 with an identical profile, give it ethernet, scsi adapter,etc..

no matter what I do , it says not scsi devices found.
Yes, because you seemingly have only one SCSI adapter, for chrissakes! You can add this adapter to several LPARs in the same way you can promise the same 10-Dollar-bill to several people. But finally, either you are going to have as many bills as people you made a promise to or all (except one) are going to be very disappointed. What you see is a LPAR which you have promised a SCSI adapter which it cannot get because you gave it to another system first. Switch off the first LPAR and you perhaps can boot the second LPAR without a problem (but as long as it runs you will not be able to boot the first - for the same reasons).

Quote:
Originally Posted by computron
If I sound completely off the rails frustrated , it's because I am..
Well, i run some 40 managed systems with about 300 LPARs distributed on them, more or less the whole midrange IT of a big bank. I dare say if the system would be so bad as you describe that should not be possible. I might start with

Quote:
I've set up HMC v8.2, and run it through a VM on a Vmware esxi server.
which is a non-supported setup. You might not know that, because reading the documentation is below real experts, but this - along with several other necessary things you may not have done and things you didn't do according to the requirements - may also have led to your frustration. It takes very little creativeness from my side to come up with a possible course of action leading to the problems you encounter.

So you might want to reconsider your take on this and start with learning and only critisize things you have a well-founded knowledge about.

I hope this helps.

bakunin

Last edited by bakunin; 05-14-2015 at 02:39 PM..
 

10 More Discussions You Might Find Interesting

1. AIX

LPAR creation

can i get a step b syep explanation in creating LPAR... i have searched for tutorials i couldn't find the right one.... (2 Replies)
Discussion started by: udtyuvaraj
2 Replies

2. AIX

LPAR freezes after switching of storage (lpar is mirrored)

Hi all, I have the following configuration 2 ds3524 storage disk systems located over 2 locations 2 P720 server located over 2 locations DS3524 are connected to san switch. Each vio server has 1 fc adapter attached to a san switch. per p720 server 2 virtual io servers. Vio 1 has 1 lun... (2 Replies)
Discussion started by: markiemark
2 Replies

3. AIX

PowerVM HA questions

hi guys, i need to develop following setup for a customer: high availability oracle database on aix7 and linux in 2 different LPAR using dual ps700 blande a ds3400 and HMC. the question is, it is possible to have automatic vioc failover(aix,linux) when for example 1 vios goes down? in... (6 Replies)
Discussion started by: gullio23
6 Replies

4. Solaris

Package creation problems with Source files

Hi, I am creating "LSOF" solaris package from solaris "source" files. I have compiled the source file and with that i created prototype file also. Then using pkgmk command i can make the package . In the package i am having (pkginfo pkgmap reloc) two file and one directory respectively But... (3 Replies)
Discussion started by: Kathirvel G
3 Replies

5. AIX

Need IBM PowerVM

Hi all please give me a link for IBM PowerVM (4 Replies)
Discussion started by: babinlonston
4 Replies

6. Windows & DOS: Issues & Discussions

Problems With User Creation Script

Hello everyone, I've been attempting to make a program which creates user accounts from a file which contains the usernames required. It also checks if the directory of the username exists in the C:\Users directory and then is going to give the option to delete the directory, or rename it, this... (1 Reply)
Discussion started by: charlieabee
1 Replies

7. AIX

Some questions about Intellistation 285 and powervm

Some simple questions about Intellistation 285 and powervm. I want to learn AIX,so i will buy an used I285 from ebay. 1)Will support aix 7.1? 2)Is powervm avaliable?Where to download or buy it? Thanks (3 Replies)
Discussion started by: Linusolaradm1
3 Replies

8. AIX

How to differentiate between a standalone LPAR and a VIOC (which again is a lpar)?

There can be configurations in IBM Server wherein a standalone partition is created on some supported IBM Server Or A VIOS - VIOC LPARs created. Now in both cases they are lpars. But if I want to differentiate b/w a standalone LPAR vs an VIOC LPAR how can I do..? On a... (2 Replies)
Discussion started by: Manish00712
2 Replies

9. AIX

PowerVM SEA etherchannel performance ?

Hello, POWER7 machine. 4 x 1Gbit port ethernet adapter is dedicated to vios. 8023ad etherchannel is created using those 4 ports. Etherchannel adapter is shared to lpars using SEA. If I test network performance directly from vios partition (using iperf) I'm geting nice 4Gbit throughput. But if... (3 Replies)
Discussion started by: vilius
3 Replies

10. AIX

Powervm ivm vios

Hello, After installing on P6 which is POWERVM IVM VIOS enabled (VET CODE D21C77ACD9229817CA1F00002C10004164 ) i get this message "I/O hosting requires a hosting partition - boot not permitted". HMC was connected to the machine then HMC was removed through ASMI Searching on... (2 Replies)
Discussion started by: filosophizer
2 Replies
All times are GMT -4. The time now is 07:45 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy