Sponsored Content
Operating Systems Linux IPV6 ip getting deleted after ping Post 302943820 by muzaffar.k on Wednesday 13th of May 2015 06:04:00 AM
Old 05-13-2015
I am not using any dhcp server here, I am assigning it statically.
same thing works for Redhat client but we are facing the issue on fedora OS
PHP Code:
inet6 addr7878:12::10/64 Scope:Global 
Its correct I.P,

is there anything which I need to enable..?
 

9 More Discussions You Might Find Interesting

1. AIX

IPv6 on AIX

Hi Every1, I want to configure IPv6 on AIX and want to communicate between IPv4 machine IP and IPv6 machine. Is it possible? (2 Replies)
Discussion started by: Shrek
2 Replies

2. SuSE

Linux and IPv6

Hi gurus, In a few month, we must enable IPv6 on our Linux Server! Should we reinstall the Linux machine to enable IPv6 or could we just make some change in configuration's files? Could Linux run simultaneous IPv4 and IPv6? Thanks in advance for our help our ideas? Best regards, nm (3 Replies)
Discussion started by: hiddenshadow
3 Replies

3. Shell Programming and Scripting

[ASK] How to check whether ipv4 or ipv6 and ping those IP

I have perl script that I use to check and ping a list of ip, The problem is, I didnt understand how to ping ipv6 on perl, Could I use Ping::External??And how could I get the ping result (reply or not)? This is my code #!/usr/bin/perl -- use Net::Ping; use Data::Validate::IP; use... (3 Replies)
Discussion started by: franzramadhan
3 Replies

4. Shell Programming and Scripting

Animation Ping on Solaris Like Cisco Ping

Hi, I develop simple animation ping script on Solaris Platform. It is like Cisco ping. Examples and source code are below. bash-3.00$ gokcell 152.155.180.8 30 Sending 30 Ping Packets to 152.155.180.8 !!!!!!!!!!!!!.!!!!!!!!!!!!!!!. % 93.33 success... % 6.66 packet loss...... (1 Reply)
Discussion started by: gokcell
1 Replies

5. Shell Programming and Scripting

How to get reason for ping failure using perls Net::Ping->new("icmp");?

Hi I am using perl to ping a list of nodes - with script below : $p = Net::Ping->new("icmp"); if ($p->ping($host,1)){ print "$host is alive.\n"; } else { print "$host is unreacheable.\n"; } $p->close();... (4 Replies)
Discussion started by: tavanagh
4 Replies

6. Solaris

IPv6 question

I am currently trying to setup static ipv6 address with a persistent default gateway. This is on a Solaris 10 non global zone running inside a Solaris 10 global zone. My production server I am comparing against is a Solaris 10 xen instance running on a Oracle Solaris xen instance. I have got... (12 Replies)
Discussion started by: jpolachak
12 Replies

7. UNIX for Dummies Questions & Answers

Assigning ipv6 to bonding interface - getting old as well as changed ipv6 in ifconfig output

Hi, I have created a bonding bond1 interface with 6 Eth , mode=4. Recently i have changed my old ipv6 to new one and tried to restart as well as reload network service. Post which i can see old as well as changed ipv6 in ifconfig command output. Below are few files and command output for your... (1 Reply)
Discussion started by: omkar.jadhav
1 Replies

8. Programming

Ping test sends mail when ping fails

help with bash script! im am working on this script to make sure my server will stay online, so i made this script.. HOSTS="192.168.138.155" COUNT=4 pingtest(){ for myhost in "$@" do ping -c "$COUNT" "$myhost" &&return 1 done return 0 } if pingtest $HOSTS #100% failed... (4 Replies)
Discussion started by: mort3924
4 Replies

9. UNIX for Beginners Questions & Answers

Just can't turn off ipv6?

I'm running a Linux OS that uses Debian as it's base. A commercial vpn is installed that uses OpenVPN. For some reason, I can't get ipv6 to tunnel properly .... and Ipleak.net shows that my location is being unmasked by ipv6. I've tried kernel commands at boot, I've tried sysctl.conf commands.... (2 Replies)
Discussion started by: benc
2 Replies
PHP_STRIP_WHITESPACE(3) 						 1						   PHP_STRIP_WHITESPACE(3)

php_strip_whitespace - Return source with stripped comments and whitespace

SYNOPSIS
string php_strip_whitespace (string $filename) DESCRIPTION
Returns the PHP source code in $filename with PHP comments and whitespace removed. This may be useful for determining the amount of actual code in your scripts compared with the amount of comments. This is similar to using php -w from the commandline. PARAMETERS
o $filename - Path to the PHP file. RETURN VALUES
The stripped source code will be returned on success, or an empty string on failure. Note This function works as described as of PHP 5.0.1. Before this it would only return an empty string. For more information on this bug and its prior behavior, see bug report #29606. EXAMPLES
Example #1 php_strip_whitespace(3) example <?php // PHP comment here /* * Another PHP comment */ echo php_strip_whitespace(__FILE__); // Newlines are considered whitespace, and are removed too: do_nothing(); ?> The above example will output: <?php echo php_strip_whitespace(__FILE__); do_nothing(); ?> Notice the PHP comments are gone, as are the whitespace and newline after the first echo statement. PHP Documentation Group PHP_STRIP_WHITESPACE(3)
All times are GMT -4. The time now is 10:35 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy