Dear Experts,
I put below command-
could you please describe the outputs column-
let me describe some them-
col_1: (10.131.60.48.55880) The IP address of the local computer and the port number being used for this particular connection appear in the Local Address column.
col_2:... (3 Replies)
Hi,
Does anyone know why I get a different output when using "netstat -a" or "netstat -an" ??
# netstat -a | grep ts15r135
tcp 0 0 nbsol152.62736 ts15r135.23211 ESTABLISHED
# netstat -an | grep 172.23.160.78
tcp 0 0 135.246.39.152.51954 ... (4 Replies)
hi all,
when I run-
wcars1j5#netstat -an | grep 8090
127.0.0.1.8090 *.* 0 0 49152 0 LISTEN
wcars1j5#
1. does this mean that no one is connected to this port?
Regards,
akash (1 Reply)
I can't tell what the output of the netstat command means. Is there anywhere that has this information? I tried the man pages, but they weren't helpful. (3 Replies)
I have a TCPIP server application (a Vendor package) which by default allows 10 connections. It provides a parameter to allow us to increase the maximum allowable connections in case it is needed. Intermittently this application is failing with maximum number of connections reached even when there... (1 Reply)
Hi,
I'm trying to figure out how much traffic has been generated and received from netstat -s output (using Linux). I can see the output shows packet counts and Octet values, how would I correctly calculate how much traffic in and how much out?
My output below:
Ip:
88847576 total... (1 Reply)
Hi,
I have old SCO O/S. System keeps crashing. I made lot of changes to kernel but so for nothing helped. I wrote a script which takes netstat -an output every one minute. I saw some thing right before the system crashed. Not sure if this means anything..
uname -a
SCO_SV djx2 3.2... (2 Replies)
Hi All,
I am trying to collect the listen ports info from netstat command in centos 7
From that info i am trying to collect all the foreign address IP for those ports.
I am using below script to do the same.
netstat -an |grep -w "LISTEN" |grep -v "127.0.0.1" |awk '{print $4}' >... (3 Replies)
Discussion started by: sravani25
3 Replies
LEARN ABOUT OPENDARWIN
traceroute6
TRACEROUTE6(8) BSD System Manager's Manual TRACEROUTE6(8)NAME
traceroute6 -- print the route IPv6 packets will take to the destination
SYNOPSIS
traceroute6 [-dlnrv] [-f firsthop] [-g gateway] [-m hoplimit] [-p port] [-q probes] [-s src] [-w waittime] target [datalen]
DESCRIPTION -d Debug mode.
-f firsthop
Specify how many hops to skip in trace.
-g gateway
Specify intermediate gateway (traceroute6 uses routing header).
-m hoplimit
Specify maximum hoplimit.
-l Print both host hostnames and numeric addresses. Normally traceroute6 prints only hostnames if -n is not specified, and only numeric
addresses if -n is specified.
-n Do not resolve numeric address to hostname.
-p port
Set UDP port number to port.
-q probes
Set the number of probe per hop count to probes.
-r
-s src Src specifies the source IPv6 address to be used.
-v Be verbose.
-w waittime
Specify the delay time between probes.
RETURN VALUES
The traceroute6 command will exit with 0 on success, and non-zero on errors.
SEE ALSO ping(8), ping6(8), traceroute(8)HISTORY
The traceroute6 command first appeared in WIDE hydrangea IPv6 protocol stack kit.
BSD May 17, 1998 BSD