I suspect you are in for a lot of late nights....
Restore a mksysb from a mirrored system to a single disk....hmmm
A mksysb that takes 3 DVD's...hmmm
Clean install and a preservation restore might be your best bet.
LVM redbook is you next step I think:
And this is worth a read:
HTH
Hello again,
We need to install patches to HP-UX B.11.11 but would like to break the mirror it has (with out damaging it) so that in case of failure we can use this a meassure procedure.
Any ideas on how to do this
Thank you! (2 Replies)
Hi All,
How do you know if you need to break the mirror on solaris 8 patch update?
Here's the patch example, 117350-54. On the site, it's just a low type update and not a medium or critical.
Is breaking a mirror a best practice only or really a requirement to some patch?
Thanks,
itik (1 Reply)
Hi All,
How do I break the solaris 8 mirror? And how do I make sure I will point the first hd mirror on reboot.
If the first break mirror won't boot. How do I make the copy mirror to boot?
Thanks in advance,
itik (2 Replies)
Hello
I have a question
I have a box with Aix 5.3 with rootvg on mirror.
I deleted a filesystem and I create a new one to install some software but when I type lsvg -l rootvg all my filesystems has mirror unless the new one.
My question is I can mirror this fs only ??? or I have to... (9 Replies)
We are considering a DR strategy of booting AIX 5.3 and 5.3 logical partitions from EMC Symmetrix SAN disks, so that we can replicate via SRDF to a recovery site. Has anyone tried configuring AIX 5.x systems to boot from SAN disk? If so, can you provide any information on the pros and cons of... (6 Replies)
Guys,
In my AIX 6.1 box the rootvg was on hdisk2, I tried to migrated it to hdisk0
Added hisk0 to rootvg , mirrored rootvg and changed bootlist and and sucessfully rebooted from hdisk0
Now I tried to remove the hdisk2 from rootvg so breaked mirror
-bash-3.00# unmirrorvg rootvg hdisk2... (3 Replies)
Hello all,
I need help for erasing IBM P5 machine running AIX 5.3.
I have 2 system disks (Hardware mirror) and i'm looking for a way like a LIVE CD bootable CD so I can boot with the cd and then format the system disks with a "secure erase" software. (7 Replies)
Hello:
I have a machine built on 2 drives and mirrors have been created to a second set of 2 drives (4 total) on the same platform. SVM.
Might anyone provide guidance to create a second machine by breaking the mirrored set, moving the two mirrors (2) to another machine (same platform type),... (1 Reply)
Hello,
Few days ago I created both mksysb and savevg archives of rootvg.
How can I restore this rootvg now because the AIX crashed during some software tests. There is no way to start from hdisk0 because most of the system files are deleted (this includes libc.a).
I tough it will be trivial... (6 Replies)
Hi Guys,
I have a mirrored LVM volume, and wish to break the mirror leaving only copy1 (effectively removing copy 0).
Here's the config:
# lvs -a -o +devices
lvdata vg01 mwi-ao 2.19T lvdata_mlog 100.00 lvdata_mimage_0(0),lvdata_mimage_1(0)
vg01... (0 Replies)
Discussion started by: badoshi
0 Replies
LEARN ABOUT SUSE
irsend
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)